0
0

Lee 90860 Carbide Factory Crimp Die, 9mm Luger – Taper Crimp

UPC: 734307908607

$21.99

33 in stock

Online inventory may differ from in-store availability. 

Fast Shipping

Quick turnaround so you get your gear sooner.

Secure FFL-Friendly Checkout

Trusted checkout with industry-standard protection.

Family-Owned Business

Keeping Traditions Alive Since 1953

Secure Transactions provided with

Description

The Lee 90860 Carbide Factory Crimp Die takes the guesswork out of the final step on your 9mm Luger reloads. It does two jobs in one pass through the press: a carbide ring at the base post-sizes the case to spec while the crimp sleeve puts a clean taper crimp on the mouth. The result is a finished round that chambers freely and feeds smoothly, which is exactly what you want running pistol ammo through a semi-auto.

Because 9mm Luger headspaces on the case mouth, this die applies a taper crimp rather than a roll crimp. That matters. A taper crimp removes the flare and holds the bullet without rolling the mouth into the bullet, so your rounds still headspace correctly. The adjustable crimp sleeve lets you dial in exactly how much crimp you want, then lock it down so every round that follows comes out the same.

What the Lee 90860 Brings to Your Reloading Bench

The carbide sizing ring is the standout here. It's ground to maximum allowable case diameter, so if a seated bullet bulged the case wall a touch, this die irons that back down into spec. That's a common cause of rounds that won't quite chamber, and this die cleans it up. One nice bonus is that case trim length isn't critical with this die, so you can skip a lot of the trimming and chamfering fuss that other crimp methods demand.

Getting the Most Out of the 9mm Carbide Factory Crimp Die

Setup is straightforward. You back the crimp sleeve off, thread the die in, then bring it down in small increments until you've removed the flare and set enough tension to prevent bullet setback. A light touch is all you need on 9mm. Most folks run it as a standalone fourth station on a progressive press or as a final pass on a single stage. It threads into any standard 7/8-14 press, so it drops right into whatever setup you're already running.

If you've been chasing the occasional round that hangs up on the feed ramp or won't fully seat in the chamber, this die is one of the simplest fixes on the bench.

Key Specifications

  • Manufacturer: Lee Precision
  • Manufacturer Part Number: 90860
  • Model Number: 90860
  • UPC: 734307908607
  • Caliber: 9mm Luger (9×19)
  • Die Style: Carbide Factory Crimp Die
  • Crimp Type: Taper Crimp
  • Sizing Ring Material: Carbide
  • For Use With: Pistol Cartridges
  • Dies In Set: 1
  • Thread: 7/8-14
  • Length: 4.9 in
  • Shipping Weight: 0.35 lb

What’s Included

  • Lee 90860 Carbide Factory Crimp Die (single die)
  • Lock ring
  • Instruction sheet

Frequently Asked Questions

Does the Lee 90860 apply a roll crimp or a taper crimp to 9mm?

It applies a taper crimp. Since 9mm Luger headspaces on the case mouth, a taper crimp is the correct choice because it holds the bullet and removes flare without rolling the mouth over. Lee uses roll crimps only on their dies for rimmed, revolver-style cartridges that headspace on the rim.

What makes the carbide version different from a standard crimp die?

The carbide ring in the base post-sizes the case while the crimp is applied, bringing the case body back down to maximum allowable spec. If a seated bullet bulged the case a little, this die corrects it, which helps rounds chamber freely. A standard taper crimp die only crimps and does not resize the case body.

Do I still need to trim my 9mm brass if I use this die?

Trim length isn't critical with the Factory Crimp Die, so you can skip a lot of the trimming and chamfering step. The die works off the case body and mouth to set a consistent crimp regardless of small length variations. That saves real time on a reloading session.

Will the Lee 90860 fit my press?

Yes, it uses standard 7/8-14 threads, so it fits virtually any single stage, turret, or progressive press on the market. It's commonly run as a dedicated final crimp station on progressive presses. Just thread it in, set your crimp, and lock the ring.

Additional information

UPC

734307908607

Manufacturer

Manufacturer Part Number

90860

Caliber/Gauge

9mm

Length

4.9000

Product Type

Factory Crimp Pistol Die

Shipping Weight

0.35

Reviews

There are no reviews yet.

Be the first to review “Lee 90860 Carbide Factory Crimp Die, 9mm Luger – Taper Crimp”