Description
The Lee Carbide Factory Crimp Die for .40 S&W and 10mm Auto earns a spot on just about every pistol reloading bench, and for good reason. This single die does two jobs at once: it applies a firm taper crimp to lock the bullet in place, then runs the whole loaded round past a carbide sizing ring ground to maximum allowable case diameter. The result is a cartridge that drops cleanly into the chamber without fuss, which is exactly what you want when you're cranking out range ammo or match loads.
What the Lee Factory Crimp Die Actually Does
Think of this as your insurance policy at the end of the loading process. The carbide ring in the base post-sizes the finished round, so if a case picked up a small bulge from a slightly oversized bullet, or you went a touch heavy on the crimp and raised a buckle, the die smooths it right back out as the cartridge withdraws. That's a big help if you shoot a .40 with a less-supported chamber, where fired brass tends to swell at the base. Trim length isn't critical either, which saves you a step compared to the fussier parts of rifle reloading.
Setting Up the .40 S&W / 10mm Crimp Die
Adjustment is straightforward. The crimp ring floats, and the adjusting screw lets you dial in exactly how much crimp you want and repeat that setting batch after batch. A lot of folks run it as the final station on a progressive press like a Dillon, letting it kiss the occasional round that needs a little help. It uses standard 7/8-14 threads, so it threads into any common press from Lee, Hornady, RCBS, Lyman, and others. No shell holder is required for normal use since the round seats against the carbide ring itself.
Reloaders who shoot a lot of mixed range brass tend to love this die because it takes the guesswork out of case variation. If you run cast or lead bullets, just keep an eye on crimp pressure so the carbide ring isn't swaging the bullet down, and seat and crimp in separate steps for the cleanest results. For bulge busting the base of semi-auto cases, this same die pairs with Lee's separate Bulge Buster kit.
Key Specifications
- Manufacturer: Lee Precision
- Manufacturer Part Number (MPN): 90862
- UPC: 734307908621
- Caliber: .40 S&W / 10mm Auto
- Product Type: Factory Crimp Pistol Die
- Crimp Style: Taper Crimp
- Dies In Set: 1
- Sizer Material: Carbide
- Thread Size: 7/8-14
- Shell Holder Included: No
- Storage Box Included: Yes
- Country of Origin: United States
- Shipping Weight: 0.4 lbs
- Length: 4.85 in
What’s Included
- Lee Carbide Factory Crimp Die (.40 S&W / 10mm Auto)
- Storage box
- Instructions
Frequently Asked Questions
Does the Lee Carbide Factory Crimp Die apply a taper or roll crimp?
On autoloader cartridges like the .40 S&W and 10mm Auto, this die applies a taper crimp, which is the correct style for rimless pistol rounds that headspace on the case mouth. A taper crimp secures the bullet without crushing the mouth you need for proper headspacing. The adjusting screw lets you set exactly how much crimp you want.
What does the carbide ring in this crimp die do?
The carbide ring sits in the base of the die and post-sizes the entire loaded round as it's withdrawn, ground to the maximum allowable case diameter. If a round has a small bulge from an oversized bullet or a buckle from too much crimp, the ring smooths it back out so the cartridge chambers reliably. That's why many reloaders can run mixed range brass and still have rounds that pass the plunk test in tight chambers.
Will this die fit my press?
Yes. It uses the standard 7/8-14 thread, so it threads into common single-stage and progressive presses from Lee, Dillon, Hornady, RCBS, Lyman, and others. Plenty of people run it as the final station on a progressive to finish each round.
Can I use the Lee Factory Crimp Die with cast or lead bullets?
You can, and many do, but keep an eye on your crimp setting. Because the carbide ring sizes to a set diameter, too much crimp pressure on a thick case can swage an oversized cast bullet down slightly. Seating and crimping in separate operations and not overdoing the crimp keeps your lead loads performing their best.




Reviews
There are no reviews yet.