Description
The Lee Carbide 3-Die Set in .40 S&W/10mm is one of those reloading staples that just works. The carbide sizing die uses a solid carbide insert ground to a special contour, which means you can skip the case lube step most of the time and still get smooth, even sizing. That carbide ring is ground to avoid leaving the belt mark you sometimes see on cases from cheaper carbide dies, so your brass comes out clean and consistent pass after pass.
What You Get in the Lee .40 S&W/10mm Die Set
Three dies cover the whole process. The carbide full-length sizing die resizes the case and deprimes it in one stroke, which is key if you're loading brass fired in more than one gun or picking up mixed range pickups. The powder-through expanding die flares the case mouth and lets you charge powder at the same time, working great with a dipper or an auto-disk measure. The bullet seating die finishes the job, seating the bullet and removing the flare, so you don't need a separate taper crimp die for most loads.
Loading 10mm Auto With the Same Set
One of the nicer things about this set is the dual-caliber coverage. To switch from .40 S&W over to 10mm Auto, you back the bullet seating die and powder-through expanding die out about one and three-quarter turns. The same sizing die and shell holder handle both rounds. Just note that 10mm load data isn't printed on the included sheet, so you'll want to grab Lee's Modern Reloading manual or another trusted source for those recipes.
Folks who've run these dies tend to point to the build quality and value, and they hold up well for higher-volume reloading. If you want to split seating and crimping into two steps down the road, Lee's separate Carbide Factory Crimp Die drops right into the same caliber lineup. Out of the box, though, this three-die set has everything needed to start turning out solid .40 and 10mm ammo.
Key Specifications
- Manufacturer: Lee Precision
- Manufacturer Part Number (MPN): 90799
- UPC: 734307907990
- Caliber: .40 S&W / 10mm Auto
- Product Type: Carbide 3-Die Set (Pistol)
- Die Style: Carbide Kit
- Dies in Set: 3
- Sizing Lube Required: No (carbide)
- Shipping Weight: 1.27 lbs
What’s Included
- Carbide full-length sizing die
- Powder-through expanding die
- Bullet seating die
- Universal shell holder
- Powder dipper (measure)
- Instructions and load data
Frequently Asked Questions
Does the Lee Carbide 3-Die Set load both .40 S&W and 10mm Auto?
Yes, this set handles both cartridges. To load 10mm Auto instead of .40 S&W, you back out the bullet seating die and the powder-through expanding die about one and three-quarter turns. The included load data sheet covers .40 S&W, so for 10mm recipes grab Lee's Modern Reloading manual or another trusted load source.
Do I need case lube with these carbide dies?
No, the carbide sizing die means you can skip the lube step for most pistol reloading. The solid carbide insert is ground to a special contour that sizes smoothly without the usual lubrication. That alone saves time and keeps your bench a lot cleaner.
Is a separate crimp die needed with the Lee .40 S&W/10mm set?
For most loads, no. The bullet seating die removes the case mouth flare as it seats, which eliminates the need for a separate taper crimp die in typical use. If you'd rather separate seating and crimping, Lee offers a Carbide Factory Crimp Die in this caliber that drops into the same setup.
Will this die set work on a progressive press?
Yes, these are standard 7/8-14 threaded dies that fit single-stage, turret, and progressive presses. The powder-through expanding die is built to charge the case while flaring the mouth, which pairs nicely with an auto-disk measure on a progressive setup. It's a popular choice for higher-volume .40 and 10mm reloaders.




Reviews
There are no reviews yet.