Description
Loading for the .30 Mauser, also known as the 7.63x25mm, can be tricky when dies for the old bottleneck cartridge are hard to find. This Lee Precision steel 3-die set covers the whole job in one box, and plenty of folks grab it to feed their 7.62x25mm Tokarev pistols too, since the cases run close enough to share a die set. Everything threads 7/8-14, so it drops right into Lee, Dillon, Hornady, Lyman, RCBS, and just about any standard single-stage or progressive press.
What the Lee .30 Mauser Steel Die Set Does on the Press
The set handles decapping, sizing, case mouth expanding, powder charging, bullet seating, and crimping without needing a separate taper crimp die. The steel full-length sizing die is ground to a special contour that resizes the case cleanly without leaving the ugly belt mark that cheaper steel dies tend to stamp in. The powder-through expanding die flares the mouth just enough for easy bullet insertion while letting you charge the case in the same stroke, which keeps your rhythm smooth on the press.
Dialing In the Bullet Seater
The bullet seating die is where this set earns its keep. It uses a free-floating seater to keep bullets lined up straight for better accuracy, and the adjustable crimp runs from a slight taper all the way to a full roll. Because the expander only flares the bare minimum, the seating die wipes out that flare as it crimps, which is why you can skip the extra taper crimp die entirely.
Keep in Mind With These Steel Dies
Unlike Lee's carbide sets, the steel sizer needs case lube before you run brass through it, and cases should be clean going in. That is the trade-off for the lower price, and most reloaders consider it a fair deal for a cartridge this specialized. Set it up once, use a little resizing lubricant, and it will knock out consistent .30 Mauser and 7.62x25mm ammo load after load.
Key Specifications
- Manufacturer: Lee Precision
- Manufacturer Part Number (MPN): 90755
- Model: Steel 3-Die Set
- UPC: 734307907556
- Cartridge: .30 Mauser (7.63x25mm / 7.62x25mm)
- Number of Dies: 3
- Die Types: Full-Length Sizing, Powder Through Expanding, Bullet Seating
- Die Material: Steel
- Thread Size: 7/8-14
- Lube Required: Yes, case lubricant needed for sizing
- Gun Type: Handgun
- Country of Origin: United States
- Shipping Weight: 1.2125 lbs
What’s Included
- Steel full-length sizing die with decapping unit
- Powder through expanding die
- Bullet seating die
- Universal shell holder
- Powder dipper
- Load data / instructions
- Plastic storage case
Frequently Asked Questions
Will this Lee .30 Mauser die set also load 7.62x25mm Tokarev?
Yes, many reloaders use this set to load 7.62x25mm Tokarev since the .30 Mauser (7.63x25mm) and Tokarev cases are dimensionally very close. It is a common go-to when dedicated Tokarev dies are hard to track down. Always confirm your load data and check your sized and seated rounds for proper fit in your chamber.
Do I need case lube with these dies?
Yes. These are steel dies, not carbide, so the sizing die requires case lubricant before you run brass through it. Your cases should also be clean before charging. Lube up, and sizing stays smooth and avoids stuck cases.
Do I need a separate taper crimp die with this set?
No. The bullet seating die handles crimping with an adjustable range from a slight taper to a full roll crimp. Since the expander flares the case mouth just enough for bullet insertion, the seating die removes that flare as it crimps, so a separate taper crimp die is not needed.
What presses will this die set fit?
The dies use the standard 7/8-14 thread, so they fit all common presses including Lee, Dillon, Hornady, Lyman, and RCBS. That covers most single-stage and progressive presses on the market. Just thread them in and adjust to your setup.


Reviews
There are no reviews yet.