$149.99
9 in stock
Online inventory may differ from in-store availability.
Quick turnaround so you get your gear sooner.
Trusted checkout with industry-standard protection.
Keeping Traditions Alive Since 1953
Secure Transactions provided with 
A standard carbine buffer is just aluminum and a few steel weights, and it does the bare minimum. The KynSHOT RB5000 replaces that dead weight with a sealed hydraulic system that absorbs and dissipates the energy from your bolt carrier's rearward travel instead of just slamming into the back of the buffer tube. The payoff is a smoother, softer cycle, noticeably less muzzle rise, and that annoying spring twang all but disappears. KynSHOT rates it at a 30% reduction in felt recoil, and the difference is most obvious on your second and third shots when you're trying to stay on target.
Inside, the RB5000 uses patented damping technology to slow the bolt carrier and prevent bolt bounce as a fresh round chambers. That translates to less recovery time between shots and a sight picture that often never leaves the optic. It's a proven design that's logged serious use with competition shooters, law enforcement, and the armed forces, and it's rated for full-auto fire. The whole unit is machined from high-strength 17-4 stainless steel with Mil-Spec hydraulic fluid and seals, certified to run from -30F all the way up to 150F.
This one is engineered for any AR-15 running a Mil-Spec carbine buffer tube with a 7-inch internal depth and a collapsible stock. It drops right in as a direct replacement and pairs with any standard buffer spring, so installation is about as simple as swapping your old buffer out. It also covers a wide spread of AR-15 calibers beyond 5.56, including .223, 7.62×39, 6.5 Grendel, 6.8 SPC, 350 Legend, and 450 Bushmaster, plus AR-10 platforms like the POF Revolution that use the same carbine-length tube.
If you shoot 3-Gun, run a lot of rapid strings, or just want a friendlier-shooting rifle, this is a worthwhile upgrade. It's also a favorite for newer shooters and anyone dealing with shoulder issues, since a calmer recoil impulse makes the whole gun easier to run. Keep in mind this is the standard model, so heavily suppressed or over-gassed setups may be better served by the RB5000HP, and it's not meant for pistol-caliber carbines.
Yes, the RB5000 is a direct drop-in replacement for a standard carbine buffer and works with any Mil-Spec buffer spring. It's designed for AR-15s using a Mil-Spec carbine buffer tube with a 7-inch internal depth and a collapsible stock. Installation is as simple as pulling your old buffer and dropping this one in its place.
KynSHOT rates it at up to a 30% reduction in felt recoil along with greatly reduced muzzle rise. The improvement shows up most on follow-up shots, where your sight picture tends to stay on target and target reacquisition time drops. Owners often describe the shooting experience as noticeably softer and smoother than a standard weighted buffer.
Yes. Beyond .223 and 5.56, the RB5000 is compatible with a range of AR-15 calibers including 7.62×39, 6.5 Grendel, 6.8 SPC, .204, 350 Legend, and 450 Bushmaster. It also works in AR-10 platforms that share the same carbine-length buffer tube, such as the POF Revolution and Ruger SFAR.
The standard RB5000 is built for typical AR-15 carbine gas systems. If you're running a heavily suppressed or over-gassed rifle, or a thumper like .50 Beowulf, the RB5000HP is the better call. It should not be used in pistol-caliber or direct-blowback PCCs, where models like the RB5007, RB5015HD, or RB5020SS are recommended instead.
| UPC | 854476005003 |
|---|---|
| Manufacturer | |
| Manufacturer Part Number | RB5000 |
| Color | HYDRAULIC RECOIL BUFFER |
| Length | 7.7500 |
| Model | |
| Product Type | Buffer |
You must be logged in to post a review.
Reviews
There are no reviews yet.