$47.00
18 in stock
Online inventory may differ from in-store availability.
Quick turnaround so you get your gear sooner.
Trusted checkout with industry-standard protection.
Keeping Traditions Alive Since 1953
Secure Transactions provided with 
The KZ-INFLEX2 is Kick-EEZ's answer to the factory Inflex 2 pad that ships on a lot of newer Browning shotguns. It's a pre-fit replacement, meaning it's already molded to the correct profile and mounts up using your existing factory screws with a 3-9/16 inch hole spacing. The heart of it is Sorbothane, a viscoelastic polymer that absorbs impact and then fully recovers between rounds, so it keeps performing shot after shot without bottoming out. Kick-EEZ rates the material at up to 94 percent recoil reduction, and the way it works is smart: instead of pushing energy straight back at you, it channels that force out the sides of the buttstock.
This pad is a direct swap for Browning models running the Inflex 2 system, including the New A5, BPS, 725 Citori, and Maxus II. It also crosses over to a number of Winchester guns built on the same pad platform, like the SX4 and XPR families. If your gun left the factory with an Inflex 2 pad on it, this drops right into its place. Worth measuring your stock against the templates before ordering, since stock dimensions can drift a bit with age, temperature, and humidity.
Foam and cheaper rubber pads tend to compress and quit absorbing after repeated use. Sorbothane is a different animal, rated to cycle millions of times and hold up across a wide temperature range, which is why it shows up on heavy-recoiling waterfowl and turkey rigs. That quick recovery between shots is a real advantage during long clay sessions or a morning of high-volume dove hunting, where a mushy pad leaves you sore by the end.
Swapping it is about as simple as gun work gets. Back out the two factory screws, pull the old Inflex 2 pad, set the KZ-INFLEX2 in place, and snug the screws back down. The surface is slip-resistant so it holds its spot in the shoulder pocket without grabbing your clothes when you mount the gun. Made in the USA, black finish, and there are no internal air pockets, so if you ever want to fine-tune the fit it can be ground down like the rest of the Kick-EEZ lineup.
It's a direct replacement for Browning models running the Inflex 2 pad, including the New A5, BPS, 725 Citori, and Maxus II. It also fits select Winchester guns built on the same platform, such as the SX4 and XPR. If your gun came from the factory with an Inflex 2 pad, this one drops into its place.
It's about as easy as it gets. The KZ-INFLEX2 uses your existing factory screws with a 3-9/16 inch hole spacing, so you back out two screws, pull the old pad, set the new one on, and snug the screws back down. No stock modification is needed for a standard swap.
Sorbothane is a viscoelastic polymer that absorbs impact and fully recovers between shots, so it doesn't bottom out the way foam or cheap rubber does over time. Kick-EEZ rates it at up to 94 percent recoil reduction, and it works by channeling energy out the sides of the stock instead of straight back into your shoulder. That translates to less fatigue and quicker follow-up shots.
Yes. Since the pad has no internal air pockets, it can be ground down like the rest of the Kick-EEZ lineup if you want to fine-tune the fit to your exact stock. Because stock dimensions can vary with age and humidity, it's smart to check your measurements against the templates before you start grinding.
| UPC | 730412202029 |
|---|---|
| Manufacturer | |
| Manufacturer Part Number | KZ-INFLEX2 |
| Color | Black |
| Model | |
| Product Type | Recoil Pad |
You must be logged in to post a review.
Reviews
There are no reviews yet.