0
0

Hornady Match Grade Bushing .246 – 22 Cal Neck Sizing Bushing

UPC: 090255592467

$23.99

2 in stock

Online inventory may differ from in-store availability. 

Fast Shipping

Quick turnaround so you get your gear sooner.

Secure FFL-Friendly Checkout

Trusted checkout with industry-standard protection.

Family-Owned Business

Keeping Traditions Alive Since 1953

Secure Transactions provided with

Description

This is the .246 bushing (Hornady part number 594246) for the Match Grade Bushing die system. It drops into the Hornady Match Grade full length and neck sizing dies and gives you direct control over how much your case necks get squeezed down. Because it is self-centering inside the die body, the brass stays aligned through the sizing stroke, which is where a lot of runout and inconsistency gets introduced with older setups.

What the .246 Hornady Match Grade Bushing Does

Standard dies size your necks all the way down to SAAMI minimum and then open them back up with an expander ball, which overworks the brass more than most loads need. A bushing like this one lets you skip that back-and-forth. You pick the inside diameter that matches your brass and bullet, and the neck gets sized just enough to hold the bullet with the tension you're after. Less sizing means less brass flow, less annealing frequency, and more consistent necks from case to case. The .246 size falls into the .22 caliber range alongside the .242, .244, and .248 bushings, and reloaders commonly reach for these when loading .223 Remington and 22-250 Remington.

Picking the Right Size for Your Brass

The easiest way to land on the correct bushing is to measure the outside neck diameter of a loaded or dummy round with a good micrometer, then subtract .001 to .003 inches to account for brass spring-back and the neck tension you want. Keep in mind neck wall thickness varies by brass brand, so what works with one headstamp may need a size up or down with another. Most handloaders end up keeping a few bushings on hand in .002 inch increments to fine tune once they see how their particular rifle, brass, and chamber behave.

These bushings are machined in the USA and made to tight tolerances, which is the whole point of running a match grade setup. Get the sizing right at the press and you'll see it pay off in consistency downrange.

Key Specifications

  • Manufacturer: Hornady
  • Manufacturer Part Number: 594246
  • UPC: 090255592467
  • Bushing Diameter: .246 in
  • Caliber Range: .22 Cal
  • Type: Self-Centering Neck Sizing Bushing
  • Compatibility: Hornady Match Grade Full Length & Neck Sizing Dies
  • Size Increments: .002 in between bushing sizes
  • Quantity: 1 bushing
  • Country of Origin: Made in USA

What’s Included

  • One Hornady Match Grade .246 neck sizing bushing

Frequently Asked Questions

What dies does the Hornady Match Grade .246 bushing fit?

It fits the Hornady Match Grade Bushing dies, both the full length sizing die and the shoulder bump neck sizing die. The bushing is sold separately from the die set, so you add the size your cartridge and brass require. It is self-centering, so it lines itself up inside the die body during sizing.

How do I know if .246 is the right bushing size for my loads?

Measure the outside neck diameter of a loaded or dummy round with a micrometer, then subtract about .001 to .003 inches for brass spring-back and your desired neck tension. Since neck wall thickness changes with different brass brands, the .246 may be ideal for one setup and off by a thousandth or two for another. Many reloaders keep a couple sizes on either side so they can dial it in.

What calibers is the .246 bushing typically used for?

The .246 sits in the .22 caliber group of bushings. Reloaders commonly use bushings in this range, including .242, .244, .246, and .248, for cartridges like .223 Remington and 22-250 Remington. Your exact size still depends on your brass and the neck tension you want.

Why use a bushing instead of a standard sizing die?

A standard die sizes the neck down to minimum spec and reopens it with an expander, which works the brass harder than many loads need. A bushing lets you size the neck just enough for proper bullet grip, so you reduce overworking the brass and improve neck consistency. That consistency is what helps tighten groups at the range.

Additional information

UPC

090255592467

Manufacturer

Manufacturer Part Number

594246

Reviews

There are no reviews yet.

Be the first to review “Hornady Match Grade Bushing .246 – 22 Cal Neck Sizing Bushing”