Description
Reaching into the press to balance a bullet on every case is the part of progressive reloading that slows everyone down. The Hornady Lock-N-Load Bullet Feeder Die solves that for 40 S&W and 10mm Auto by dropping a seated-ready bullet onto the case for you, so your hands stay on the handle and your rhythm never breaks. It runs on a twin-collet system that feeds one bullet at a time, and the whole thing is case-activated, meaning a bullet only releases when a case rises up into the die. No case, no bullet, which keeps things clean and predictable.
How the Lock-N-Load Bullet Feeder Die Earns Its Spot
The collets are machined from solid steel, so this is a part you set once and run for years. It threads into any press with standard 7/8"-14 die stations, whether you're on a Hornady Lock-N-Load AP, a Dillon, a Lee, or a turret press. Plenty of folks run it even without the tube or hopper setup, just dropping bullets straight into the die by hand because it's faster and easier than placing each one on the case mouth. Hornady notes the full bullet feeder system can bump reloading speed up to 50 percent once you've got it dialed in.
Dialing In Your 40 / 10mm Feeder Die
Setup is straightforward and needs no special tools. Keep in mind the die drops the bullet only, so your case mouth still needs to be belled at the powder station or with a separate expander die beforehand. The die ships with a PTX (Powder Through Expander) insert that handles that flare job on compatible Hornady powder measures. Give the collet fingers a quick check out of the box and spread them slightly if needed for smooth, drop-every-time feeding. Once it's set, it's one less thing to think about on a long loading session.
What You'll Notice at the Bench
For anyone loading pistol ammo in volume, this die turns a fiddly manual step into a hands-free one. It pairs naturally with Hornady's bullet tubes for 40/10mm if you want to go full auto-feed, or stands on its own as a simple bullet-drop helper. The inside finish comes well polished, which reloaders consistently call out as a reason feeding stays smooth.
Key Specifications
- Manufacturer: Hornady
- Manufacturer Part Number: 095332
- UPC: 090255953329
- Caliber: .40 S&W / 10mm Auto
- Die Type: Bullet Feeder Die
- Number of Dies: 1
- Collet Material: Solid steel
- Feeding: Case-activated, twin-collet, one bullet at a time
- Thread Size: 7/8"-14
- Carbide: No
- Length: 6.8 in
What’s Included
- Hornady Lock-N-Load Bullet Feeder Die (40 S&W / 10mm Auto)
- Powder Through Expander (PTX) insert
- Storage box
Frequently Asked Questions
Does the Hornady bullet feeder die bell or flare the case?
No, this die drops the bullet onto the case only. The case mouth needs to be belled ahead of time, either at your powder station or with a separate expander die. The die does include a PTX (Powder Through Expander) insert that handles the flare on compatible Hornady powder measures.
Will this die work on presses other than a Hornady Lock-N-Load AP?
Yes. It uses standard 7/8"-14 die threads, so it fits any progressive, turret, or single-stage press with those stations, including Dillon and Lee setups. On a Lock-N-Load AP you can mount it in a bushing for fast, pre-set caliber swaps.
Can I use the Hornady bullet feeder die without the tubes or hopper?
Absolutely. Many reloaders run it as a simple bullet-drop die, just dropping a bullet into the die by hand instead of placing it on each case. It's faster and lets you keep your eyes on the current operation, though pairing it with Hornady's 40/10mm bullet tubes gives you full hands-free feeding.
What's the deal with the two collets inside this die?
The die uses a twin-collet system that holds the bullet stack and releases a single bullet when a case pushes up into the die. Out of the box, it helps to check the collet fingers and spread them just a touch if feeding isn't smooth, which is a common quick tune-up. Once set, the solid steel collets hold up for years of loading.




Reviews
There are no reviews yet.