Description
Glock's polymer frames are tough and reliable, but that factory texture can leave your hand searching for purchase, especially with sweaty palms or a hard-charging range session. Hogue built the Wrapter to fix that without changing the shape or bulk of your pistol. It's a thin adhesive rubber wrap that heats up, molds to the exact contours of your frame, and stays put.
What makes this different from a slip-on sleeve is the thickness, or lack of it. The material is roughly 30% thinner than a standard credit card, so your Glock 17, 17MOS, 34MOS, 45, 45MOS or 19X Gen 5 keeps its factory dimensions and holster fit while gaining a noticeably grippier surface. The block texture bites into your palm just enough to steady the gun under recoil without feeling rough or abrasive during extended range time.
Installing the Hogue Wrapter Grip
The kit comes as a multi-piece set cut specifically for the Gen 5 No Backstrap frame, so every panel lines up with the slide release, magazine release, and trigger guard without extra trimming. Clean the frame with the included alcohol pad, warm the rubber with a hair dryer or heat gun until it's pliable, then press and mold it into place. Once it cools, the adhesive sets and the grip becomes a semi-permanent part of the gun. Leftover material gives you a little wiggle room to patch a corner or customize coverage on your own.
Built for Daily Carry and Range Duty
Whether this Glock rides in a duty holster, sits in a nightstand safe, or gets run hard at competition, the added texture pays off most when your hands aren't perfectly dry. It's a simple, low-cost upgrade for anyone who wants better retention and control without swapping frames or sending the gun out for stippling.
Hogue Wrapter Fit and Compatibility
This particular Wrapter is cut for the Gen 5 frame with no backstrap, covering the 17, 17MOS, 34MOS, 45, 45MOS and 19X models. Double check your generation and backstrap setup before ordering, since Hogue makes separate versions for Gen 3, Gen 4, and other backstrap configurations.
Key Specifications
- Manufacturer: Hogue
- Model: Wrapter
- Manufacturer Part Number: 17178
- UPC: 743108171783
- Color: Black
- Material: Adhesive rubber
- Texture: Block
- Backstrap: None
- Fitment: Glock 17, 17MOS, 34MOS, 45, 45MOS, 19X (Gen 5 – No Backstrap)
- Profile Thickness: Approximately 30% thinner than a standard credit card
- Shipping Weight: 0.228 lbs
What’s Included
- Hogue Wrapter multi-piece adhesive rubber grip panels
- Alcohol prep pad for frame cleaning
- Leftover remnant material for custom trimming
Frequently Asked Questions
Will the Hogue Wrapter change how my Glock fits in my holster?
No, that's the whole point of the ultra-thin design. Since the material sits at roughly 30% thinner than a credit card, most factory and aftermarket holsters made for Gen 5 Glocks will still work fine after installation.
Is the Wrapter permanent, or can I remove it later?
It's designed as a long-term grip enhancement using heat-activated adhesive, so it's meant to stay on once installed. It can be peeled off with some effort and adhesive remover if you decide to switch textures down the road, but it's not meant to be swapped on and off like a slide-on sleeve.
Do I need any special tools to install the Wrapter?
Just a hair dryer or heat gun to warm the rubber and activate the adhesive, plus the alcohol pad that's included in the box to clean the frame first. No screws, glue, or gunsmithing required.
How do I know which Wrapter fits my Glock?
This version is cut specifically for Gen 5 frames with no backstrap, covering the 17, 17MOS, 34MOS, 45, 45MOS, and 19X models. Hogue makes separate part numbers for Gen 3 and Gen 4 frames, so it's worth confirming your generation and backstrap style before buying.





Reviews
There are no reviews yet.