Description
The Forster 6mm Creedmoor Bushing Full Length Die Kit gives you real control over neck tension while still doing the work of a standard full length die. Instead of relying on a fixed expander to set your bullet grip, the interchangeable bushing sizes the neck to the exact diameter you want. At the same time, the die sizes the case body and bumps the shoulder back to set correct headspace, so your reloads chamber smoothly in a factory 6mm Creedmoor rifle.
What the Forster Bushing Full Length Die Does Differently
Traditional full length dies work the neck down with the die body, then open it back up with an expander ball, which can overwork brass over time. A bushing die lets you size the neck just enough to grip the bullet and no more. The payoff is more consistent neck tension and longer case life, since the brass isn't getting squeezed and stretched more than it needs to be. The bushing itself floats in the die, and you can adjust its height to size the full neck or just a portion of it, which is handy when you're chasing the best groups.
Three Bushings Picked for 6mm Creedmoor
This kit ships with three bushings sized 0.270 inch, 0.272 inch, and 0.274 inch, which Forster selected specifically for 6mm Creedmoor brass. That spread covers the common range reloaders land on, so one of the three will typically get you right around the industry-standard 0.002 inch of neck tension. If you run tighter or looser tension, you can step up or down and fine-tune from there. The die body is machined to tight tolerances and the internals are hand polished to a mirror finish, which cuts friction and keeps your cases from getting scuffed as they move through.
Fits Forster Co-Ax and Standard Presses
The die uses a standard 7/8-14 thread, so it drops right into a Forster Co-Ax press or any traditional threaded single-stage press. It's a smart upgrade for precision-minded 6mm Creedmoor shooters who want benchrest-level consistency without jumping straight to a full custom setup.
Key Specifications
- Cartridge: 6mm Creedmoor
- Die Style: Bushing Full Length Sizing Die
- Included Bushings: 0.270", 0.272", 0.274"
- Thread: 7/8-14
- Material: Steel
- Finish: Hand polished internals
- Manufacturer: Forster Products
- Manufacturer Part Number: FBK4331
- UPC: 757253990533
- Country of Origin: USA
- Shipping Weight: 0.515 lbs
What’s Included
- One Forster Bushing Full Length Sizing Die
- Three neck bushings (0.270", 0.272", 0.274")
- Instructions
Frequently Asked Questions
What bushings come with the Forster 6mm Creedmoor Bushing Full Length Die Kit?
The kit includes three bushings sized 0.270 inch, 0.272 inch, and 0.274 inch. Forster picks these specifically for 6mm Creedmoor brass, so one of the three usually lands you right around the common 0.002 inch of neck tension. You can move up or down within that set to fine-tune your bullet grip.
How do I pick the right bushing size for my brass?
Measure the outside neck diameter of a loaded round with the bullet seated, then subtract your desired neck tension. For a standard 0.002 inch of tension, subtract 0.002 inch from that loaded neck measurement and choose the closest bushing. Keep in mind that brass with uneven neck wall thickness can affect your results, so neck turning helps if you want the most consistent tension.
What's the difference between a bushing die and a standard full length die?
A standard full length die sizes the neck with the die body and then opens it back up with a fixed expander ball, while a bushing die uses an interchangeable bushing to size the neck to the exact diameter you choose. That means you set neck tension by swapping bushings rather than changing expanders. The bushing approach works the brass less, which helps consistency and can extend case life.
Will this die work in a Forster Co-Ax press?
Yes. The die uses a standard 7/8-14 thread, so it fits a Forster Co-Ax press as well as any traditional threaded single-stage press. No special adapter is needed.




Reviews
There are no reviews yet.