Description
There is a reason so many custom rifle builds start with a Bergara barreled action. Instead of sourcing an action, hunting down a barrel blank, and paying a gunsmith to chamber and headspace everything, you get a matched pair from one of the most respected barrel makers in the business, ready to drop into any Remington 700 footprint stock or chassis. This one is chambered in .300 PRC, which has become the go-to magnum for long range hunting and precision work thanks to its ability to run heavy, high BC bullets efficiently.
What the Premier Barreled Action Brings to a .300 PRC Build
The 22 inch barrel is machined from 416 stainless in a No.4 contour with fluting, the same setup Bergara runs on their Canyon rifle. That contour hits a sweet spot between a pencil-thin mountain barrel and a heavy target tube, stiff enough for consistent groups but light enough to carry into rough country. Total weight comes in at 4.2 pounds, so you have plenty of room to build a packable hunting rig or add a heavier stock for range duty. The 1:9 twist stabilizes the long, heavy bullets the .300 PRC was designed around, and the 5/8×24 threaded muzzle ships with a thread protector so you can spin on a brake or can whenever you are ready.
Bergara Premier Action Details That Matter
The action itself features a spiral fluted bolt body, enlarged bolt handle, sliding plate extractor, and dual ejectors for positive extraction and ejection with fat magnum cases. The receiver is drilled and tapped for 8-40 screws, the beefier hardware serious long range guys prefer for keeping scope bases put under magnum recoil. The raw stainless finish looks sharp as-is and shrugs off weather, or it gives your Cerakote applicator a clean canvas.
Finishing Out Your Bergara .300 PRC Project
Pair it with a quality stock or chassis, a Rem 700 pattern trigger, and a bottom metal setup that feeds long magnum cartridges, and you have the bones of a rifle that will hang with builds costing far more. For anyone wanting Bergara barrel accuracy without buying a complete rifle, this is the smart way in.
Key Specifications
- Manufacturer: Bergara
- Manufacturer Part Number: BPBA26-300PRC
- UPC: 043125030071
- Caliber: .300 PRC
- Action Type: Bolt Action
- Barrel Length: 22 inches
- Barrel Contour: No.4 Fluted
- Barrel Material: 416 Stainless Steel
- Twist Rate: 1:9
- Muzzle Thread: 5/8×24 with Thread Protector
- Footprint: Remington 700
- Scope Mounting: Drilled and Tapped for 8-40 Screws
- Weight: 4.2 lbs
- Finish: Raw Stainless (Silver)
What’s Included
- Bergara Premier Series barreled action
- Thread protector (installed on 5/8×24 muzzle)
Frequently Asked Questions
Will the Bergara Premier barreled action fit Remington 700 stocks and chassis?
Yes, this barreled action is built on a Remington 700 footprint, so it drops into most Rem 700 pattern short of long action-specific fitment concerns. Since .300 PRC is a long action magnum, make sure your stock or chassis inlet, bottom metal, and magazines are set up for long action magnum cartridges. Minor bedding or barrel channel work may be needed depending on the stock.
Does this barreled action come with a trigger or bottom metal?
No, you get the barreled action with a thread protector and nothing else. You will need to add a Remington 700 pattern trigger, a stock or chassis, and bottom metal with magazines that feed .300 PRC. That is the whole point of a barreled action, it lets you pick every other component to suit your build.
What is the 1:9 twist good for in .300 PRC?
The 1:9 twist is the standard for .300 PRC and stabilizes the heavy, high ballistic coefficient bullets the cartridge was built around, including 212 to 230 grain match and hunting loads. That makes this barrel a strong choice for long range hunting and precision shooting where those sleek bullets shine.
Is the 22 inch barrel long enough for .300 PRC?
You will give up some velocity compared to a 26 inch tube, typically in the neighborhood of 100 to 150 fps depending on the load. In exchange you get a rifle that is noticeably handier, especially once a suppressor goes on the 5/8×24 threads. For a hunting build that gets carried more than it gets benched, most folks find the trade well worth it.




Reviews
There are no reviews yet.