Description
The Banish 45/46 series was built around one simple idea: one suppressor, many hosts. This M13.5×1 left-hand piston is what makes that swap happen. Thread it into the rear of your Banish 45 or 46, match it to a barrel cut for M13.5×1 LH, and you are ready to run. It is a small part that does a big job, letting you move the same can between different guns without buying a whole new suppressor for each one.
What the Banish 45/46 M13.5×1 LH Piston Is Made For
M13.5×1 LH is the left-hand metric thread you will find on a lot of European-influenced pistols, including certain Glock, SIG, and H&K barrels. If your host has that pattern, this is the piston that lines up with it. The left-hand callout matters, so remember it threads opposite of what most folks expect: lefty to tighten. The piston is engraved with the thread diameter, pitch, and direction so there is no second-guessing which one is in your hand when you have a drawer full of them.
Built to Take the Heat
Banish machines these from heat-treated steel, which is the right call for a part that soaks up muzzle blast and cycles under pressure every shot. On a tilting-barrel pistol, the piston works as a booster, letting the can float forward briefly so the slide cycles like the suppressor was not even there. That is the difference between a gun that runs reliably suppressed and one that chokes. This piston is calibrated for .45 ACP host barrels wearing M13.5×1 LH threads.
Keeping Your Kit Straight
Think of pistons as the keys to your Banish. Each one unlocks a different host, and having the right thread on hand means you are never stuck at the range with a can you cannot mount. Pick up the patterns that match your pistols and keep them labeled. Installation is tool-free and takes about a minute once the suppressor is disassembled from the rear.
Key Specifications
- Manufacturer: Banish (Silencer Central)
- Model: Pistons
- Manufacturer Part Number: 100000311292
- UPC: 810171225481
- Thread Pattern: M13.5×1 LH (left-hand)
- Caliber: .45 ACP
- Compatibility: Banish 45 and Banish 46 suppressors
- Material: Heat-treated steel
- Color: Silver
- Length: 2.95 in
- Marking: Engraved thread diameter, pitch, and direction
- Product Type: Silencer accessory / piston
What’s Included
- One Banish 45/46 M13.5×1 LH piston
Frequently Asked Questions
What guns use the M13.5×1 LH thread on this Banish piston?
M13.5×1 LH is a left-hand metric thread common on certain European-influenced pistol barrels, including some Glock, SIG, and H&K models. Check your host barrel's stamped thread spec or measure it before ordering. If the barrel is cut for M13.5×1 LH, this piston will match it.
Does this piston fit both the Banish 45 and the Banish 46?
Yes, this piston is made for the Banish 45 and Banish 46 modular suppressor systems. It threads into the rear of the can in place of whatever piston is currently installed. Just make sure you are running the correct Banish body and this piston will drop right in.
Why is this a left-hand thread and how do I install it?
The LH in M13.5×1 LH means the threads run opposite of standard, so you tighten to the left and loosen to the right. Installation is tool-free once the suppressor is opened from the rear, and it takes about a minute. The piston is engraved with its thread size and direction so you can always confirm which one you are handling.
Do I need the spring or a fixed barrel spacer with this piston?
For tilting-barrel pistols that move during recoil, you run the piston with its spring so the can boosts and cycles the action properly. For pistol-caliber carbines or subguns with fixed barrels, you would swap to a fixed barrel spacer instead. Match your setup to the host so the gun cycles the way it should.




Reviews
There are no reviews yet.