Description
Redding's Type S Bushing Full Length Sizing Die for 6x47mm Lapua does something a standard sizer can't: it sizes the full case body, bumps the shoulder, and controls exactly how much you squeeze the neck, all in one stroke. The secret is the interchangeable bushing system. Instead of relying on a fixed inside diameter and an expander ball dragging back through the neck, you drop in a bushing that sizes the outside of the neck to precisely where you want it. Less working of the brass means longer case life and straighter ammo, which is exactly what the 6×47 Lapua crowd is after.
Why the Type S Bushing Die Changes Your 6x47mm Lapua Loads
Neck tension is one of the biggest levers you have when chasing small groups, and this die hands you full control over it. Bushings are sold in .001-inch increments, so you can tune grip to the exact wall thickness of your brass. The common starting point is to measure the outside diameter of a loaded round and subtract .002 inches, which leaves a touch of spring-back and the right amount of tension for a bolt gun. From there you can step up or down a thousandth at a time to find what your rifle likes. The bushing floats slightly in the die so it self-centers on the neck, which helps keep runout low.
Setting Up Your 6x47mm Lapua Bushing Die
The adjustable decapping rod lets you reposition the bushing to size only part of the neck when you want, leaving a section fireformed to your chamber. It's worth noting bushings and a shellholder are sold separately, so plan on grabbing a bushing or two sized to your loaded round. Pull the bushing and the internals and the die doubles as a body die for brass you only want to bump.
Built the Way Redding Builds Everything
The die comes with both a standard sizing button and a decapping pin retainer, so you can run the expander or skip it entirely and let the bushing do all the neck work. Threaded in the industry standard 7/8-14, it drops into any common single stage or progressive press. Redding has been turning out dies on precision tooling since the 1940s, and the fit and finish here is right in line with that reputation.
Key Specifications
- Manufacturer: Redding
- Manufacturer Part Number: 77489
- UPC: 611760774898
- Cartridge: 6x47mm Lapua
- Die Type: Type S Bushing Full Length Sizing Die
- Bushing System: Interchangeable, .001-inch increments (sold separately)
- Thread: 7/8-14 industry standard
- Decapping Rod: Adjustable for partial neck sizing
- Doubles As: Body die when bushing and internals are removed
What’s Included
- One Redding Type S Bushing Full Length Sizing Die
- Decapping rod
- Standard sizing button
- Decapping pin retainer (for use in place of the button)
- Die storage box
- Instructions
Frequently Asked Questions
Do I need to buy bushings separately for this 6x47mm Lapua Type S die?
Yes. The die ships without bushings, so you'll want to add at least one sized to your brass. Measure the outside diameter of a loaded round and subtract about .002 inches to get a solid starting bushing, then fine tune from there. Many reloaders end up keeping two or three bushings on hand since neck wall thickness varies between brass brands and lots.
Can the Type S full length die also work as a body die?
It can. Remove the bushing and the internal decapping assembly and the die will size the body and bump the shoulder without touching the neck. That flexibility is handy if you want to pair it with a separate mandrel or neck sizing step down the road.
What neck tension should I run with the 6x47mm Lapua bushing die?
A good baseline for a bolt gun is around .002 inches of tension, meaning the bushing is .002 smaller than the outside diameter of your loaded round. Some rifles shoot better with a bit more grip, so stepping to .003 is a common experiment. Because bushings come in .001-inch increments, you can test and lock in whatever your barrel prefers.
Will this die fit a standard reloading press?
Yes. It uses the industry standard 7/8-14 thread, so it threads right into any common single stage or progressive press. You will need the correct shellholder for 6x47mm Lapua, which is sold separately.





Reviews
There are no reviews yet.