Description
If you shoot 6mm XC and want to pull the last bit of accuracy out of your handloads, the Forster Ultra Micrometer Seater Die is the kind of tool that earns its spot on the bench. It builds on Forster's original Bench Rest Seater design and adds an ultra-accurate micrometer head, so you can set and repeat bullet seating depth without the guesswork that usually comes with dialing in a new load.
The heart of this die is its sliding die chamber. Instead of only supporting the case neck or rim, it cradles the bullet, case, and seating stem together inside one close-fitting chamber through the entire stroke. That co-axial setup keeps everything in line and produces rounds with very little runout, which is exactly what you want when you're chasing tight groups. It's a non-crimping design that press-fits the bullet in perfect alignment, and the seating stem is machined with enough clearance to seat on the ogive rather than the tip, so it plays nicely with long VLD and high-BC match bullets.
Why the Ultra Micrometer Seater Die Changes Your Bench Routine
The micrometer head is where this die really pays off. Gradations are marked at .001 inch and you can fine-tune in either direction down to .0005 inch, with bright white markings that are easy to read under bench lighting. Seat your bullet close, measure it, then dial the stem to the exact length you need. If you run several bullet styles through the same rifle, just record each "optimal" setting and spin the micrometer right back to it next session.
Build Quality Behind the Forster 6mm XC Seater
Forster machines these dies from high-quality steel to tight tolerances, and each one is hand polished before and after heat treating for a clean, consistent finish. It also carries the Forster Cross Bolt Die Locking Ring, which clamps the split ring shut rather than driving a set screw into the die threads, so your settings stay put and the threads stay unmarred. Made in the USA, it threads into standard 7/8-14 presses and gets you straight to load development.
Key Specifications
- Manufacturer: Forster Products
- Manufacturer Part Number: U00044
- UPC: 757253999390
- Cartridge: 6mm XC
- Die Style: Bullet Seating Die
- Die Line: Ultra Micrometer Seater
- Seating Type: Non-crimping, straight-line (co-axial)
- Micrometer Adjustment: .001 inch gradations, adjustable to .0005 inch
- Locking Ring: Forster Cross Bolt Die Locking Ring
- Thread: 7/8-14 (standard press compatible)
- Material: Hand-polished, heat-treated steel
- Country of Origin: Made in USA
What’s Included
- Forster Ultra Micrometer Seater Die (6mm XC)
- Forster Cross Bolt Die Locking Ring
- Bullet seating stem
- Instruction sheet
Frequently Asked Questions
How fine can I adjust seating depth with the 6mm XC Ultra Micrometer Seater Die?
The micrometer head is marked in .001 inch gradations and can be fine-tuned in either direction down to .0005 inch. Seat a bullet, measure it, then dial the stem to your exact target length. The bright white markings make it easy to read and repeat your settings.
Will this die seat long, high-BC match bullets?
Yes. The seating stem is machined with extra clearance so it contacts the bullet on the ogive rather than the tip, which makes it well suited for long VLD and high-BC match projectiles. That contact point also helps keep seating consistent across different bullet shapes.
Does the Forster 6mm XC seater die crimp the case?
No, this is a non-crimping seater die. It press-fits the bullet while holding the case and bullet in alignment inside the sliding die chamber, which is what produces the straight, low-runout rounds these dies are known for.
Does the Ultra Micrometer Seater Die fit standard reloading presses?
It uses the standard 7/8-14 thread and works with most common single-stage and turret presses. It also ships with Forster's Cross Bolt Die Locking Ring, which clamps the split ring shut instead of digging a set screw into the die threads, so your setup stays locked in.




Reviews
There are no reviews yet.