Description
The Lee Precision TL356-95-RF is a six-cavity mold built for folks who cast in volume and want to keep their lead cost down. It drops a .356 diameter 95 grain round-with-flat-nose bullet, with a finished overall length right around .405 inches. That light 95 grain weight makes it a natural fit for 380 Auto, though plenty of casters run these through 9mm Luger and 38 Super for soft-shooting target and plinking loads that sip alloy compared to the heavier 124 grain stuff.
What Makes the TL356-95-RF Tick
Lee machines these blocks from aluminum rather than iron or steel, and that pays off in a few real ways. Aluminum heats up and cools down quicker, so you get good bullets after just a few warmup pours, and the blocks weigh about a third of what steel does, which your hands will thank you for during a long session at the pot. The cavities are CNC machined for tight roundness and size control, and most bullets come out ready to load as cast once you lube them. The TL designation means it has a tumble-lube style groove, so it plays nicely with a lube like Liquid Alox or a powder coat.
Built for Heavy Duty Casting Sessions
This is Lee's commercial-quality six-cavity design, so the blocks run steel bushings and alignment pins to hold registration pour after pour. The sprue plate is hard anodized and cam operated, held down with spring washers at each end, which cuts out the hammering you deal with on cheaper molds. The handle attached to the sprue plate is included.
A Note on Handles
Like all of Lee's six-cavity molds, this one does not come with the mold handles needed to open and close the blocks. You'll want to grab a set of Lee six-cavity handles (part 90005) if you don't already have them, and the good news is they fit any of Lee's six-cavity blocks, so one set covers your whole collection. A molded storage case is included to hold the mold once it's set up with handles.
Key Specifications
- Manufacturer: Lee Precision
- Manufacturer Part Number: 90672
- UPC: 734307906726
- Cavities: 6
- Bullet Diameter: 0.356 in
- Bullet Weight: 95 Grains
- Bullet Style: Round Flat Nose (RF), tumble lube
- Bullet Overall Length: 0.405 in
- Suggested Cartridges: 380 Auto, 9mm Luger, 38 Super Auto
- Block Material: Machined Aluminum
- Sprue Plate: Hard Anodized, Cam Operated
- Country of Origin: USA
- Shipping Weight: 1.3125 lbs
What’s Included
- Six-cavity TL356-95-RF aluminum mold blocks
- Cam-operated hard anodized sprue plate with attached handle
- Molded storage case
- Instructions
Frequently Asked Questions
Does the TL356-95-RF mold come with handles?
No, this six-cavity mold does not include the handles used to open and close the blocks, which is standard for all of Lee's six-cavity molds. You'll need a set of Lee six-cavity mold handles, part 90005, sold separately. The upside is that one set of handles fits all of Lee's six-cavity blocks, so you only buy them once.
What cartridges can I load with these 95 grain bullets?
The .356 diameter 95 grain bullets this mold casts are well suited to 380 Auto, and they also work in 9mm Luger and 38 Super for light target and plinking loads. The lighter weight uses less alloy per bullet than typical 115 or 124 grain loads, so you stretch your lead further. Always work up your loads using published reloading data for your specific cartridge.
Do I need to size these bullets after casting?
Most bullets from Lee molds can be loaded as cast without sizing, thanks to the CNC machined cavities that hold tight roundness and diameter. That said, many casters still run a sizing and lubing step for consistency. Since this is a tumble lube (TL) design, it pairs well with Liquid Alox or a powder coat finish.
Why aluminum blocks instead of steel on the TL356-95-RF?
Aluminum heats up and cools down faster than iron or steel, so you'll be dropping good bullets after just a few warmup casts. The blocks are also about a third the weight of steel, which cuts down on hand fatigue during long casting sessions. Aluminum is rust resistant too, so storage is less of a worry.



Reviews
There are no reviews yet.