Description
This is the barrel most folks should be starting with when they put together a 16" 5.56 AR-15, and for a lot of them it's the last one they'll ever need. The Gunner profile is Faxon's most popular contour, and it earns that spot by blending the rigidity of a Government-style barrel with the lighter feel of a Pencil. It keeps the heavier material back near the chamber where it does the most for heat resistance and mitigating whip, then tapers down toward the muzzle to shed weight where it isn't helping. The result is a rifle that balances closer to your body, points fast, and won't wear you out over a long day at the range or in the field.
What the Pinned Gas Block on the Gunner Barrel Saves You
Pinning a gas block used to mean drilling, careful alignment, and a fair bit of swearing. Faxon takes that off your plate by pre-notching the .625" journal and pre-drilling the included low-profile gas block, then supplying the retaining pin. On top of the set screws, that pin keeps the gas block from shifting or loosening under recoil, so your gas system stays locked in for the long haul. The mid-length gas system is the right call at 16 inches too, giving you a softer, more linear recoil impulse and less wear on the bolt and buffer over thousands of rounds.
How the Faxon Gunner Barrel Is Built
The barrel starts as certified 4150 CMV mil-spec steel and gets a QPQ salt-bath nitride finish inside and out, hardening the surface and shrugging off corrosion and wear. Every one is fully stress relieved, air-gauge tested, magnetic particle inspected, and capped with an 11-degree target crown for consistent accuracy. The 1:8 twist is the versatile all-arounder, stabilizing a wide range of 5.56 and .223 bullet weights, and the chamber is cut for both 5.56 NATO and .223 commercial loads. Reviewers consistently point to Faxon's fit, finish, and reliability being well above what the price suggests, with clean feed ramps and correctly placed gas block holes making installation painless. Made in Ohio and backed by Faxon's lifetime guarantee, it's a genuine workhorse for a general-purpose carbine, a training rifle, or a home defense build.
Key Specifications
- Manufacturer: Faxon Firearms
- Manufacturer Part Number: 15A58M16NGQ-APGB
- UPC: 816341025400
- Caliber: 5.56×45 NATO
- Barrel Length: 16"
- Profile: Gunner
- Twist Rate: 1:8
- Gas System: Mid-Length
- Gas Block: Pinned .625" Low-Profile
- Barrel Material: 4150 CMV Mil-Spec Steel
- Finish: QPQ Salt-Bath Nitride, Inside & Out
- Muzzle Thread: 1/2×28
- Crown: 11-Degree Target Crown
- Feed Ramps: M4
- Country of Origin: Made in Ohio, USA
What’s Included
- 16" Gunner profile 5.56 NATO barrel
- Pre-drilled .625" low-profile gas block
- Gas block retaining pin
Frequently Asked Questions
What size gas block does the Faxon Gunner barrel use?
The Gunner profile uses a .625" gas block journal, and the good news is the matching low-profile gas block comes in the box already pre-drilled to pin on. If you ever swap gas blocks down the road, just make sure the replacement is sized for a .625" journal. This setup is mid-length gas, so pair it with a mid-length gas tube.
Is the pinned gas block ready to install out of the box?
Faxon pre-notches the barrel journal and pre-drills the included gas block, then supplies the retaining pin, so the alignment work is already done for you. The block ships hand-tightened for transit, so you'll want to set it in place and drive the pin plus set screws before running the rifle. That pin, combined with the set screws, keeps everything locked so it won't shift or loosen under recoil.
Will a 1:8 twist stabilize the ammo I want to run?
A 1:8 twist is the do-it-all choice for 5.56 and .223, and it handles a wide range of bullet weights from lighter plinking loads up through heavier match projectiles. The chamber is cut to feed both 5.56 NATO and .223 Remington commercial ammo. Reviewers have found the Gunner does its best with quality match ammo but isn't picky about what you feed it.
What handguard length works with this 16" mid-length Gunner barrel?
With a mid-length gas system at 16 inches, most builders run a handguard in the 13 to 15 inch range to cover the gas block and give you plenty of real estate for a hand stop or grip. Just confirm your handguard clears the .625" gas block and mounts to a standard barrel nut. Because the Gunner sheds weight up front, it pairs nicely with a lightweight M-LOK rail for a fast-handling build.




Reviews
There are no reviews yet.