0
0

Forster 3-in-1 Case Mouth Cutter – 0.264in Pilot (6.5mm) 3CUT-264

UPC: 757253995903

$75.99

2 in stock

Online inventory may differ from in-store availability. 

Fast Shipping

Quick turnaround so you get your gear sooner.

Secure FFL-Friendly Checkout

Trusted checkout with industry-standard protection.

Family-Owned Business

Keeping Traditions Alive Since 1953

Secure Transactions provided with

Description

If you load a lot of 6.5mm brass, you already know case prep eats up more bench time than just about anything else. The Forster 3-in-1 Case Mouth Cutter fixes that by combining trimming, inside chamfering, and outside deburring into one motion. It slides over the cutter shaft of your Forster Original or Power Case Trimmer and locks down with a single set screw, so getting it set up takes a minute or two. This version ships with the 0.264in pilot, sized for 6.5mm cartridges like 6.5 Creedmoor, 6.5 PRC, 260 Remington, and the rest of the 6.5 family.

What the Forster 3-in-1 Cutter Does in One Pass

As you crank the case through the trimmer, carbide blades bring the case to your set length, cut a 14-degree chamfer on the inside of the case mouth, and put a 30-degree bevel on the outside. That inside angle is friendly to both standard flat-base bullets and VLD boat-tails, so seating goes smooth without shaving jacket material. Reloaders who have fussed with separate trimmers and hand deburring tools tend to notice the difference right away, with clean edges and no snags on the inside or outside of the neck.

Carbide Blades Built for the Long Haul

Forster calls this the first three-in-one cutter to run carbide blades, and that matters for anyone running volume. Used on brass, these blades are made to hold their edge for a very long time and should never need sharpening under normal use. The blades come factory adjusted on the holder, so you are getting consistent, square cuts right out of the box. Expect a pace somewhere in the range of 250 to 400 cases per hour once you get into a rhythm.

Fitting the 3-in-1 Case Mouth Cutter to Your Setup

Keep in mind this is an accessory, not a standalone unit. It needs a Forster Original or Power Case Trimmer to mount on. For cases up to 2.20 inches, the standard base on the Original Case Trimmer works fine. For longer brass, you will want the Long Base, which handles cases from about 1.00 to 3.30 inches with the 3-in-1 installed. Made in the USA.

Key Specifications

  • Manufacturer: Forster Products
  • Manufacturer Part Number (MPN): 3CUT-264
  • UPC: 757253995903
  • Pilot Diameter: 0.264in (6.5mm)
  • Compatible Calibers: 6.5mm cartridges (6.5 Creedmoor, 6.5 PRC, 260 Rem, etc.)
  • Blade Material: Carbide steel
  • Inside Chamfer Angle: 14 degrees
  • Outside Chamfer Angle: 30 degrees
  • Functions: Trim, inside chamfer, outside deburr in one step
  • Trim Rate: 250 to 400 cases per hour
  • Compatibility: Forster Original and Power Case Trimmers
  • Mounting: Slides over cutter shaft, secures with one set screw
  • Country of Origin: Made in USA

What’s Included

  • One Forster 3-in-1 Case Mouth Cutter
  • One 0.264in (6.5mm) caliber-specific pilot
  • Complete instructions

Frequently Asked Questions

Does the Forster 3-in-1 Case Mouth Cutter work on its own?

No, it is an accessory that mounts onto a Forster Original or Power Case Trimmer, which is sold separately. It slides over the cutter shaft and secures with a single set screw. If you already run one of those trimmers, this cutter drops right in.

What does the 0.264in pilot cover?

The 0.264in pilot is sized for 6.5mm cartridges, which includes popular rounds like 6.5 Creedmoor, 6.5 PRC, and 260 Remington. The pilot guides the cutter inside the case neck for a square, concentric cut. Pilot size matches bullet diameter, so this one fits the full 6.5mm family.

Do the carbide blades need sharpening?

When used on brass cases, the carbide blades are made to hold their edge for a very long time and should not need sharpening under normal use. The blades also come factory adjusted on the holder for consistent cuts right out of the box. Just keep them clean and avoid running them on anything harder than brass.

Can it handle longer rifle cases?

Yes, but the base matters. For cases up to 2.20 inches, the standard base on the Original Case Trimmer works fine. For longer brass, the Long Base handles cases from roughly 1.00 to 3.30 inches with the 3-in-1 installed.

Additional information

UPC

757253995903

Manufacturer

Manufacturer Part Number

3CUT-264

Shipping Weight

0.125

Reviews

There are no reviews yet.

Be the first to review “Forster 3-in-1 Case Mouth Cutter – 0.264in Pilot (6.5mm) 3CUT-264”