Description
Neck tension is one of those small details that separates decent handloads from the ones that print tiny groups, and this 0.333" Forster bushing gives you control over it. It drops into Forster's Bushing Bump Neck Sizing Dies and Bushing Full Length Sizing Dies, sizing the case neck down to the exact inside diameter you need for the grip you want on the bullet.
What sets these apart is how they are finished. Forster heat treats each bushing, then runs it through a cryogenic process that refines and closes up the surface of the steel. The result is an ultra smooth bore that works the brass less as it sizes, which means better concentricity, less runout, and brass that lasts longer before it needs annealing. Every bushing is honed to the precise diameter stamped on it, so the .333 you order is the .333 you get.
How the 0.333" Bushing Sizes Your Brass
The idea is simple. The bushing, not the chamber or an expander ball, determines the finished outside diameter of your case neck. Since Forster's bushing bump die runs without an expander ball, your bushing choice alone sets the neck tension. That puts the precision in your hands and keeps the brass from getting worked more than it has to.
Picking the Right Forster Neck Bushing Size
The common method is to measure the outside neck diameter of a loaded round and subtract about .002" for standard neck tension, or .003" if you want a firmer grip. A .333" bushing is a good fit for loaded necks measuring right around .335". You can also figure it from unfired components by doubling your neck wall thickness, adding bullet diameter, and subtracting for the tension you want. Bushings come in .001" increments, so a lot of reloaders keep a couple of sizes on hand to fine tune. This finish-honed accuracy matters most with uniform brass, so neck turning or consistent wall thickness will get you the most out of it.
A Note on Fit
These are made exclusively for Forster dies. They will not work in Redding or L.E. Wilson bushing dies, so make sure you are running a Forster die before you add this one to the bench.
Key Specifications
- Manufacturer: Forster Products
- Manufacturer Part Number: BUSH-333
- UPC: 757253998232
- Inside Diameter: 0.333 inch
- Type: Neck Sizing Bushing
- Material: Heat treated and cryogenically treated steel
- Size Increments: 0.001 inch
- Compatibility: Forster Bushing Bump Neck Sizing Dies and Bushing Full Length Sizing Dies
- Country of Origin: United States
What’s Included
- One Forster 0.333" neck bushing (BUSH-333)
Frequently Asked Questions
What size loaded round does the 0.333" Forster bushing work with?
This bushing is a good match for loaded rounds that measure right around .335" at the outside of the neck, since the standard approach is to subtract about .002" from your loaded neck measurement. If you want more neck tension, subtract .003" instead, which would put you closer to a loaded neck of about .336". Always measure your own loaded rounds before ordering, because brass and bullet combinations vary.
Will the Forster 0.333" bushing fit Redding or Wilson dies?
No. Forster bushings are made specifically for Forster's Bushing Bump Neck Sizing Dies and Bushing Full Length Sizing Dies. They are not compatible with Redding or L.E. Wilson bushing dies, so confirm you are running a Forster die before buying.
Why are Forster neck bushings cryogenically treated?
After the bushings are heat treated, Forster runs them through a cryogenic process that refines and closes up the surface of the steel. This creates an ultra smooth bore that sizes brass with less friction, which helps produce straighter, more consistent loaded rounds and extends the life of your brass.
Do I need an expander ball with this bushing?
Forster's bushing bump die uses a decapping assembly without an expander ball, so the bushing alone sets your neck's inside diameter and the resulting tension. That is why picking the right size matters so much. Many reloaders keep bushings in .001" increments on hand to fine tune their tension.




Reviews
There are no reviews yet.