Description
This grip module is a full aluminum replacement for the factory polymer frame on your Sig P365 XMacro. It's machined from a solid block of 7075-T6 aluminum rather than cast or injection molded, so the tolerances are tighter and the whole package feels noticeably more solid in hand than the OEM part. The Olive Drab Green finish is paired with black grip panels for a two-tone look that stands apart from the usual black-on-black setups without looking flashy.
What the Gen 3 Changes on the P365 XMacro
This third-generation module builds on the earlier Sharps Bros designs with more aggressive grip panel texturing, a redesigned steel lug system, and machining that leaves room for adding a mag funnel down the road if you want one. The trigger guard has an undercut with finger grooves worked into the geometry, letting you get a higher, more consistent grip each time you draw. Ambidextrous thumb ledges are also built into both sides of the frame, giving either hand a natural indexing point instead of favoring right-handed shooters.
Fit and Feel of the P365 XMacro Gen 3 Module
The factory grip on the XMacro runs about 1.1 inches wide, and this module bumps that up to roughly 1.3 inches. That extra material fills the hand better without turning the pistol into something hard to conceal. It also adds some weight over the polymer original, somewhere in the neighborhood of 5 ounces total, which most people notice more on the range than in the holster. That added mass helps settle the gun during recoil, so follow-up shots come a little easier.
Installing the Gen 3 on Your XMacro
This is a direct swap for the standard P365 XMacro grip module and works with any XL or X-Macro slide. It is not built for the Manual Safety FCU, so double check which fire control unit you're running before ordering. The magazine release assembly isn't included, but your factory one transfers over without issue. One thing worth knowing ahead of time: the integrated thumb ledges mean some off-the-shelf Kydex holsters will need light heat reforming to seat properly, though holsters built specifically for this module are also available.
Key Specifications
- Manufacturer: Sharps Bros
- Model: Gen 3 (G3)
- Manufacturer Part Number: SBGM05-G3-OD
- UPC: 850057873740
- Material: Billet 7075-T6 Aluminum
- Frame Finish: Olive Drab Green anodized
- Grip Panel Color: Black
- Grip Width: Approx. 1.3 inches (vs. 1.1 inch OEM polymer module)
- Weight: Approx. 5.3 ounces
- Fits: Sig Sauer P365 XMacro, compatible with any P365 XL or X-Macro slide
- Safety Compatibility: Not compatible with Manual Safety FCU
- Thumb Ledges: Ambidextrous, patented (US Patent No. 9,194,649)
- Steel Lug System: Redesigned insert
- Mag Funnel Provision: Yes, machined for optional mag funnel installation
- Trigger Guard: Enhanced geometry with undercut and finger grooves
- Magazine Release: Not included, reuse factory assembly
What’s Included
- Sharps Bros Gen 3 grip module (Olive Drab Green anodized frame)
- Black grip panels, pre-installed
Frequently Asked Questions
Will this Gen 3 grip module work on a P365 XMacro with the manual safety?
No, this particular module is not built for the Manual Safety FCU. If your XMacro has the manual thumb safety, you'll want to check with Sharps Bros for a compatible option before ordering this one.
Do I need to buy a new magazine release to install this?
No, the magazine release assembly isn't included with the grip module, but your factory Sig magazine release transfers right over. There's no need to buy a replacement unless yours is already worn out.
Will my current holster still fit once this grip module is installed?
It depends on the holster. Because of the integrated thumb ledges on both sides of the frame, most Kydex holsters need a little heat reforming to seat correctly, though holsters designed specifically for this module are also available if you'd rather skip that step.
How is the Gen 3 different from the earlier Gen 2 version of this grip module?
The Gen 3 brings more aggressive texturing on the grip panels, a redesigned steel lug system, and machining that allows for an optional mag funnel down the line. It also swaps the Gen 2's Gas Pedal style thumb rest for a slightly different ambidextrous thumb ledge design built into the frame itself.







Reviews
There are no reviews yet.