Description
Running a Victra-20 on a Beretta 20 gauge? This is the mount that makes it happen. The YHM-1355A threads directly into barrels cut for Beretta's Optima HP choke system, giving your Victra-20 suppressor a secure, dedicated attachment point without any barrel work or gunsmithing. Just spin out your choke tube, thread this in, and you're ready to hang the can.
How the Victra-20 Optima HP Mount Works
Yankee Hill took a smarter approach with the Victra series than most shotgun suppressor setups. The mount itself handles one job only: anchoring the suppressor to your choke threads. It puts zero constriction on your shot load. Pattern control comes from the choke cone that sits up front in the Victra-20's end cap, so you can swap between Improved Cylinder, Modified, and Full cones without ever touching the mount. That separation means your point of attachment stays consistent while your pattern stays adjustable, which is a genuinely clever bit of engineering for hunters who switch loads between dove fields and turkey woods.
Built to Take a Beating
This mount is machined from 17-4 stainless steel and wears a Melonite finish, the same treatment YHM puts on its rifle suppressor hardware. It shrugs off carbon, moisture, and the general abuse that comes with duck blinds and muddy field edges. Installed, it adds just 0.950 inches to your barrel length, so your gun still swings and handles like it should. The included V-20 jam nut lets you snug everything down tight so the assembly stays put through high-volume shooting.
Pairing the YHM-1355A With Your Beretta
If your 20 gauge uses Optima HP chokes, like the A400 Xplor and other current Beretta autoloaders and over-unders in 20 gauge, this is the correct mount. YHM builds these mounts brand-specific, so double check your choke system before ordering. Made in the USA and built to the same standard as the suppressor it carries.
Key Specifications
- Manufacturer: Yankee Hill Machine
- Manufacturer Part Number: YHM-1355A
- UPC: 841812103271
- Compatibility: Victra-20 suppressor on Beretta Optima HP choke threads
- Gauge: 20 Gauge
- Material: 17-4 Stainless Steel
- Finish: Melonite
- Length Added to Barrel: 0.950 in
- Shipping Weight: 0.154 lbs
- Country of Origin: Made in the USA
What’s Included
- Victra-20 Beretta Optima HP mount assembly
- YHM V-20 jam nut (YHM-1250)
Frequently Asked Questions
Which shotguns does the Victra-20 Optima HP mount fit?
This mount fits 20 gauge Beretta barrels threaded for the Optima HP (Optima-Choke HP) choke system, which covers most current Beretta autoloaders like the A400 series in 20 gauge. If your Beretta uses the older Mobil choke pattern, you'll want the YHM-1356A instead. When in doubt, check the markings on your existing choke tubes.
Does the YHM-1355A mount act as a choke?
No, and that's by design. The mount only secures the Victra-20 suppressor to your barrel and puts no constriction on the shot load. Pattern control comes from the choke cone installed in the front cap of the suppressor itself, and YHM offers Improved Cylinder, Modified, and Full cones so you can tune your pattern for the job at hand.
How much length does this mount add to my barrel?
The Victra-20 mount assembly adds 0.950 inches to your barrel when installed. That's short enough that most people leave it on full time and just run a thread protector when the suppressor is off. The included jam nut keeps the whole assembly locked down so it won't back off under recoil.
Will this mount work with the Victra-12 suppressor?
No, this one is sized for the 20 gauge Victra-20. YHM makes a separate Optima HP mount for the 12 gauge Victra-12 under part number YHM-1255A. Make sure the mount matches both your suppressor model and your shotgun's choke thread pattern.




Reviews
There are no reviews yet.