0
0

RCBS 0.325″ Steel Neck Sizing Bushing for Gold Medal Match Dies

UPC: 076683816405

$16.99

1 in stock

Online inventory may differ from in-store availability. 

Fast Shipping

Quick turnaround so you get your gear sooner.

Secure FFL-Friendly Checkout

Trusted checkout with industry-standard protection.

Family-Owned Business

Keeping Traditions Alive Since 1953

Secure Transactions provided with

Description

If you run a set of RCBS Gold Medal Match sizing dies and you've been chasing better consistency, a bushing like this 0.325" steel neck bushing is where a lot of that precision comes from. Instead of relying on a fixed expander to set neck tension, the bushing sizes the neck to the exact diameter you choose, which means you control how tightly the case grips the bullet. That control is the difference between loads that print all over the paper and loads that stack into one hole.

How the 0.325" RCBS Neck Bushing Does Its Job

This bushing is machined from bare steel and drops right into the top of a Gold Medal Match sizing die. It's self-centering, so it floats into alignment with the case neck as the case travels up, giving you even sizing all the way around rather than pushing the neck off true. Because it's unplated and in-the-white, you'll want to keep your usual case lube routine going when you run it. Reducing how much you overwork the brass also cuts down on work hardening, which stretches out case life and keeps your necks behaving the same from firing to firing.

Picking the Right Size Around the 0.325" Bushing

Sizing selection is simple once you know the math. Measure the outside neck diameter of a loaded round and subtract about .002" to .003", which leaves roughly .001" of brass spring-back for correct tension. You can also double your neck wall thickness, add bullet diameter, and subtract about .001". RCBS suggests keeping a couple of bushings above and below your target on hand, since brass and chambers vary and a two-step size-down often gives cleaner, more repeatable results than jumping straight to final diameter.

Who Reaches for the RCBS Steel Neck Bushing

This is a benchrest and long-range precision tool at heart. Handloaders who care about tight ES and SD numbers, consistent seating force, and brass that survives more reloads are the folks who lean on bushing dies. If you're building match ammo for a bolt gun fired in the same chamber, this little piece of steel earns its keep fast.

Key Specifications

  • Manufacturer: RCBS
  • Manufacturer Part Number: 81640
  • UPC: 076683816405
  • Bushing Diameter: 0.325"
  • Material: Steel
  • Finish: Bare steel, in-the-white
  • Design: Self-centering, interchangeable
  • Compatibility: RCBS Gold Medal Match series sizing dies
  • Sizing Styles: Works in full length and neck sizing dies
  • Quantity: 1 bushing
  • Country of Origin: USA

What’s Included

  • One RCBS 0.325" steel neck sizing bushing

Frequently Asked Questions

What dies does the RCBS 0.325" neck bushing fit?

It's made for RCBS Gold Medal Match series sizing dies and works in both full length and neck sizing styles. The bushing is self-centering, so it drops into the die body and aligns itself with the case neck. Redding, Wilson, and Hornady bushings can also run in RCBS Gold Medal bushing dies if you already have a drawer full of them.

How do I know if the 0.325" is the right size for my brass?

Measure the outside neck diameter of a loaded round and subtract about .002" to .003", which leaves roughly .001" of spring-back for proper tension. You can also double your neck wall thickness, add your bullet diameter, and subtract about .001". It's smart to keep a bushing or two above and below your target, since brass thickness varies and that flexibility helps you dial things in.

Does this RCBS steel neck bushing need case lube?

Yes. It comes in-the-white as bare steel rather than coated, so stick with your normal case lubrication routine when sizing. Keeping the neck lightly lubed makes for smoother, more consistent sizing and helps the brass last.

Why use a bushing instead of the standard expander ball?

A standard die sizes the neck down and then pulls an expander ball through to set tension, which can pull the neck out of alignment. A bushing sizes the neck directly to the diameter you pick, so you control tension precisely and reduce how much you overwork the brass. That translates to better accuracy and longer case life for precision loads.

Additional information

UPC

076683816405

Manufacturer

Manufacturer Part Number

81640

Reviews

There are no reviews yet.

Be the first to review “RCBS 0.325″ Steel Neck Sizing Bushing for Gold Medal Match Dies”