Description
Casting your own 7.62×39 bullets is one of the most rewarding ways to keep shooting that AK or SKS without waiting on the ammo shelf, and this Lee Precision mold is built for people who go through a lot of lead. It drops six .312" diameter, 160-grain round nose bullets per pour, so you can turn a pot of alloy into finished projectiles a whole lot faster than you would with a single or double cavity block.
What the Lee 7.62×39 6-Cavity Mold Produces
Each cavity throws a gas-checked .312" round nose bullet weighing in around 160 grains with suggested alloy, with a bullet overall length of about .960" and roughly .653" from the crimp groove to the nose. That profile feeds well through the 7.62×39 and plays nicely in a few other .311/.312 cartridges reloaders like to experiment with. Keep in mind that actual weight shifts a little depending on the alloy mix you run.
Build Quality Behind This 6-Cavity Bullet Mold
The mold blocks are CNC machined from aluminum, which keeps them rust resistant and roughly a third the weight of iron or steel blocks. That lighter weight matters more than you'd think during a long casting run since there's a lot less hand and wrist fatigue. Aluminum also heats up and cools down quicker, so you'll usually get good, fillable bullets after just a few throwaway casts to get the blocks up to temperature. Steel bushings and alignment pins keep the halves lining up true pour after pour.
Sprue Plate and Setup Notes
The hard anodized sprue plate is cam operated and held down with wave washers at each end, which takes the mallet pounding out of the equation that older molds were known for. One thing worth knowing before you order: handles are not included with this six-cavity block. You'll want Lee's commercial mold handles (part 90005) to run it. Lee also recommends smoking the cavities with a wooden match, beeswax candle, or butane lighter rather than using spray mold release, since spray can build up and shrink your bullet diameter over time.
Key Specifications
- Manufacturer: Lee Precision
- Manufacturer Part Number: 90579
- UPC: 734307905798
- Model: CTL312-160-2R
- Caliber: 7.62x39mm
- Bullet Diameter: .312"
- Bullet Weight: 160 grain
- Bullet Profile: Round Nose, Gas Checked
- Cavities: 6
- Bullet Overall Length: .960"
- Crimp Groove to Nose: .653"
- Block Material: CNC Machined Aluminum
- Sprue Plate: Hard Anodized, Cam Operated
- Weight: 1.27 lbs
What’s Included
- Lee Precision 6-cavity bullet mold block (CTL312-160-2R)
Frequently Asked Questions
Does the 7.62×39 6-cavity mold come with handles?
No, handles are sold separately for this six-cavity block. You'll want Lee Precision's commercial mold handles, part number 90005, which fit all Lee 6-cavity molds. Picking up a pair is a must before you can start casting with it.
What size bullet does this Lee mold cast?
It produces a .312" diameter round nose bullet weighing about 160 grains with a suggested alloy. The bullet overall length runs around .960". It's a gas-checked design intended for use in 7.62×39 and similar .311/.312 cartridges.
Why aluminum blocks instead of iron or steel?
Aluminum blocks are rust resistant and about a third the weight of iron or steel, which cuts down on fatigue during long casting sessions. They also heat up and cool down faster, so you'll get good bullets after just a few warm-up casts. The blocks are CNC machined for consistent roundness and sizing.
Can I use spray mold release with this mold?
Lee Precision advises against spray-type mold release products in their molds. The spray can build up in the cavities and reduce the diameter of the bullets you cast. Instead, smoke the cavities lightly with a wooden match, beeswax candle, or butane lighter to help with bullet release.





Reviews
There are no reviews yet.