Description
This is the EGW 41102 Picatinny scope base made specifically for round back Savage long action rifles. If you've got a Model 110, 111, 112, 114, or 116 (or a Stevens 200) with a round rear receiver, this rail gives you a solid, standardized mounting surface so you can run just about any Picatinny or Weaver ring set you want. It's machined from domestic 6061 T6 extruded aluminum, then tumbled, blasted, and Type II anodized in matte black for a finish that holds up to real use in the field.
Why the 20 MOA Matters on This Savage Round Back Rail
The 20 MOA built into this base angles your optic forward, which hands you extra elevation adjustment up top. That's a big deal when you're stretching a load out past where it starts to drop, since it keeps you from running out of internal travel in your scope before you get on target. For long-range work with a Savage 110 series rifle, that extra headroom is what lets you dial confidently at distance.
Fitment and Build on the EGW 110-116 Round Back Base
This one is cut for the round rear receiver pattern, so double-check your action before ordering. It fits round back long action Savages with an ejection port and the Stevens 200, but it will not fit the older flat back receivers, the Savage Axis, or the 212 slug gun. Specs come in at a 4.630 inch center spread, 7.458 inch overall length, roughly .4 inch height from the top of the receiver to the top of the rail, and about 2 ounces of weight. Full-length cross slots give you plenty of room to position rings and set your eye relief where you like it.
EGW backs it up with American manufacturing. Mounting hardware and a T-10 bit come in the box, and the recommendation is 20 inch-pounds of torque with a drop of blue thread locker to keep everything locked down through recoil.
Key Specifications
- Manufacturer: EGW (Evolution Gun Works)
- Manufacturer Part Number: 41102
- UPC: 841370105502
- Model Fitment: Savage 110, 111, 112, 114, 116, Stevens 200 (Round Rear Receiver)
- Action: Long Action, Round Back
- Elevation: 20 MOA
- Rail Type: One Piece Picatinny
- Material: Domestic 6061 T6 Extruded Aluminum
- Finish: Matte Black Type II Anodized
- Center Spread: 4.630 in
- Overall Length: 7.458 in
- Height: 0.4 in (top of receiver to top of rail)
- Weight: 2 oz
- Ring Compatibility: Picatinny or Weaver
- Country of Origin: USA
What’s Included
- EGW Savage Round Back Long Action 20 MOA Picatinny rail
- #6-48 x 1/4 mounting screws
- T-10 bit
Frequently Asked Questions
Will this EGW rail fit my Savage rifle?
It's made for round rear receiver Savage long actions, including the 110, 111, 112, 114, and 116, plus the Stevens 200. It does not fit the older flat back Savages, the Savage Axis, or the 212 slug gun. Check the shape of your rear receiver before ordering, since the round back and flat back bases are not interchangeable.
What does the 20 MOA do on this scope base?
The 20 MOA angles your optic slightly forward, which gives you extra elevation adjustment inside your scope. That matters most for long-range shooting, where you might otherwise run out of turret travel before dialing to your target's distance. For closer work it isn't required, but it doesn't hurt anything either.
What hardware comes with the EGW 41102 rail?
The base ships with #6-48 x 1/4 inch mounting screws and a T-10 bit to get it installed. EGW recommends torquing to 20 inch-pounds and adding a drop of blue thread locker so it stays put under recoil.
Can I use any scope rings with this Picatinny rail?
Yes, the full-length cross-slot design accepts standard Picatinny or Weaver rings, so you've got a lot of flexibility in ring height and brand. The cross slots also let you slide your rings fore and aft to set your eye relief where it feels right.





Reviews
There are no reviews yet.