Description
The 6mm Dasher has earned its reputation as a flat-shooting, low-recoil accuracy machine, and a cartridge that precise deserves a seater that keeps everything in line. Forster's Bench Rest Seater Die does exactly that. Instead of just holding the case neck and bullet, this die uses a sliding chamber that supports the entire outside of your sized case, so the bullet, case, and seating stem all share one common axis before seating ever begins. The result is low runout and the kind of repeatable concentricity that handloaders chase for tight groups.
How the 6mm Dasher Bench Rest Seater Die Keeps Things Straight
The heart of this die is a close-fitting, caliber-specific sliding chamber machined with a one-piece reamer. As you run the ram up, the chamber fully captures the case, then the hand-polished seating stem press-fits the bullet in perfect alignment. This is a non-crimping seater, which is exactly what you want for precision loads where you're fine-tuning seating depth rather than locking in a crimp. Forster originally patented this design decades ago, and it's still the benchmark other in-line seaters get compared to.
Why Dasher Handloaders Reach for This Forster Seater
Seating depth matters a lot with the Dasher, especially when you're chasing the lands with higher-BC bullets. Forster has refined its seating stems over the years to better fit modern ballistic tip and VLD-style projectiles, so you get clean contact and consistent seating without deforming bullet tips. Adjustment is handled with knurled knobs for quick tweaks, and the die threads into most standard 7/8-14 reloading presses. It also plays perfectly with a Forster Co-Ax press, where you won't even need a shellholder.
If you already run a full-length sizer for your Dasher brass, this seater rounds out the pair and gives you the finishing touch that turns good brass prep into genuinely accurate ammo. Built in the U.S.A. and machined to last, it's a buy-it-once piece of kit for anyone serious about this cartridge.
Key Specifications
- Manufacturer: Forster Products
- Cartridge: 6mm Dasher
- Die Type: Bench Rest Seater Die (non-crimping)
- Adjustment: Knurled knob seating stem
- Seating Style: Straight-line / co-axial with sliding chamber
- Thread: 7/8-14 standard press thread
- Country of Origin: Made in the U.S.A.
- Manufacturer Part Number: 005946
- UPC: 757253999307
What’s Included
- One Forster Bench Rest Seater Die for 6mm Dasher
- One hand-polished seating stem
- Die body split lock ring
- Complete instructions
- Die box
Frequently Asked Questions
Does the 6mm Dasher Bench Rest Seater Die use a micrometer?
No, this is the standard Bench Rest Seater Die, which adjusts using knurled knobs rather than a micrometer head. It still delivers the same straight-line seating and sliding chamber that Forster is known for. If you want a dialed-in micrometer top for repeatable depth settings, Forster offers a separate Ultra Micrometer Seater Die for the Dasher.
Will this seater die crimp my 6mm Dasher loads?
No, it's a non-crimping seater die. That's exactly what precision Dasher shooters want, since crimping isn't typically used on match loads where you're tuning seating depth to the lands. You get clean, consistent bullet seating without touching the case mouth.
Do I need a shellholder to use this Forster die?
For most standard presses, yes, you'll want the correct shellholder for the 6mm Dasher, and it's sold separately. If you're running a Forster Co-Ax press, no shellholder is needed since the press uses a universal jaw system.
Does this come with a sizing die too?
No, this listing is for the seater die on its own. If you need to size your brass as well, Forster sells a matching Full Length Sizing Die and also offers a complete Bench Rest Die Set that pairs the two together.




Reviews
There are no reviews yet.