Description
If you're loading 6.8 Western and chasing consistency, the Forster Ultra Micrometer Seater Die takes a lot of the guesswork off your bench. The micrometer head lets you fine-tune seating depth in either direction, and once you've recorded a setting you can dial right back to it when you switch bullets or come back to a load weeks later. No more trial-and-error shims or counting turns.
What makes this die tick is the spring-loaded sliding sleeve inside the body. It fully captures the case before the bullet ever starts moving, holding the bullet, case, and seating stem on a common axis through the whole stroke. That's the secret to the low runout these dies are known for, and why a lot of folks who already own Redding or RCBS micrometer seaters still reach for the Forster first.
What Sets the 6.8 Western Ultra Seater Apart
Forster machines each die from quality steel held to tight tolerances, then hand-polishes it before and after heat treating for a fine finish. This is a non-crimping style seater, so it's built purely for straight-line, press-fit seating rather than putting a crimp on your rounds. The micrometer graduations are marked in .001 inch increments with bright white markings that are genuinely easy to read and record, and you can split those down to around .0005 inch when you're tuning to the lands.
Dialing In Your 6.8 Western Loads
The process is simple: seat a bullet close to your target depth, measure it, then turn the micrometer stem up or down to land on your exact length. The die uses Forster's Cross Bolt Die Locking Ring, which clamps the split ring rather than digging a screw into the die threads. Worth knowing up front, it plays especially well with the Forster Co-Ax press since you can set it and pull it in and out without unscrewing. Made in the U.S.A. and ready to drop straight into your reloading routine.
Key Specifications
- Manufacturer: Forster Products
- Cartridge: 6.8 Western
- Die Style: Bullet Seating Die
- Adjustment Type: Micrometer, .001 inch gradations (adjustable to .0005 inch)
- Seating Style: Non-crimping, straight-line
- Material: Steel, hand-polished
- Locking Ring: Forster Cross Bolt Die Locking Ring
- Country of Origin: Made in U.S.A.
- Quantity: 1 die
- Manufacturer Part Number: U00067
- UPC: 757253990342
What’s Included
- One Forster Bench Rest Ultra Micrometer Seater Die
- One Forster split-type lock ring
- Storage case
- Instructions
Frequently Asked Questions
Does the 6.8 Western Ultra Seater Die crimp the case?
No, this is a non-crimping style seater die built for straight-line, press-fit seating. It's designed to produce concentric, match-grade rounds rather than apply a crimp. If you want a crimp, you'd add a separate crimp die to your process.
How precise is the micrometer adjustment on this die?
The micrometer head is marked in .001 inch gradations and can be fine-tuned to about .0005 inch in either direction. Once you record a setting, you can dial right back to it when swapping bullets or returning to a load. The bright white markings make reading and recording your settings easy.
Will the Forster 6.8 Western seater die work on my press?
Yes, it uses standard 7/8-14 threads and fits most common reloading presses. It pairs especially well with the Forster Co-Ax press, where you can set it and pull it in and out without unscrewing. On traditional presses, the Cross Bolt locking ring clamps the split ring instead of biting into the die threads.
What keeps the bullet concentric during seating?
A spring-loaded sliding sleeve inside the die captures the case before the bullet starts moving, holding the case, bullet, and seating stem on a common axis through the entire stroke. That alignment is what produces the low runout these dies are known for. It's a big reason reloaders chasing accuracy favor the Forster Ultra Seater.





Reviews
There are no reviews yet.