Description
The MDT 34mm Medium Premier Scope Rings are what you reach for when you want serious holding power without adding dead weight to your rifle. Machined from billet 6061 aluminum and checked on a CMM to 1.5 millionths of an inch, this matched pair clamps a 34mm scope tube with a 1.00" medium height measured from the base to the centerline of your optic. They ship in a set of two, with all the mounting hardware you need to get up and running.
What Sets the Premier Scope Rings Apart
MDT built these to a STANAG 4694 (NATO) spec, which means the ring sits flush against the top of the rail and applies pressure to the angled sides for maximum contact. That extra bite lets them clamp down on out-of-spec rails that cheaper rings would wobble on, and it works equally well on standard Picatinny and MIL-STD-1913 bases. Each ring uses four oversized #8-32 Grade 8 fasteners to clamp the scope, so there's plenty of grip for hard-recoiling calibers.
Mounting Your 34mm Premier Rings
The stepped base-to-cap interface is the real time-saver here. It lets you snug the fasteners on one side before making your final alignment, and since the rings are machined in matched pairs there's no lapping required to get a true, stress-free fit on your scope tube. Folks running everything from .308 bolt guns to 300 Win Mag report that these stay put after hundreds of rounds and hold their torque settings without drifting.
A Lightweight Mount That Earns Its Keep
At roughly 4.6 ounces for the medium set, these rings keep your build light enough for a backcountry hunt or a long day at a precision match while still feeling beefy and solid in hand. The matte black anodized finish is clean and well executed, blending into most scopes without drawing attention. For anyone cross-shopping Seekins or Vortex Precision rings, the Premier line is a strong value that doesn't cut corners on fit or finish.
Key Specifications
- Manufacturer: MDT
- Model: Premier
- Manufacturer Part Number: 103548-BLK
- UPC: 709951103753
- Scope Tube Diameter: 34mm
- Ring Height: Medium (1.00")
- Material: Billet 6061 Aluminum
- Finish: Matte Black Anodized
- Fasteners: Four #8-32 Grade 8 per ring
- Spec: STANAG 4694 (NATO)
- Rail Compatibility: Picatinny / MIL-STD-1913
- Quantity: Pair (2 rings)
- Weight: Approx. 4.6 oz per set
- Precision: CMM checked to 1.5 millionths of an inch
- Country of Origin: Canada
What’s Included
- 2 scope rings (matched pair)
- Mounting hardware
Frequently Asked Questions
Will the 34mm Premier rings fit any Picatinny rail?
Yes. These rings are built to STANAG 4694 (NATO) spec, which lets them seat solidly on both standard Picatinny and MIL-STD-1913 bases. The design actually clamps well even on rails that run slightly out of spec, so you get a secure fit on a wide range of setups.
What ring height is medium, and how do I know if it fits my scope?
Medium gives you a 1.00" height measured from where the ring meets the base to the centerline of your scope tube. That clearance works for most 34mm scopes with mid-to-larger objective bells, but it's worth checking your objective diameter against your rail height. If your bell runs big, you may want to size up to high.
Do I need to lap these rings before mounting my scope?
No lapping is required. The Premier rings are machined in matched pairs and CMM checked to tight tolerances, so they line up true right out of the box. The stepped base-to-cap interface also makes alignment straightforward without fighting uneven gaps.
What are the torque specs for the MDT Premier rings?
MDT calls for 25 to 30 inch-pounds on the clamp-to-rail screws and 15 to 22 inch-pounds on the ring cap screws. Always confirm the final cap torque against your scope maker's recommendation to avoid overtightening the tube. A quality torque wrench is your friend here.





Reviews
There are no reviews yet.