Description
The Redding Type S Small Base Bushing Full Length Die (part number 77355) takes everything that makes a bushing die great and adds small base sizing for the handloaders who need it most. It resizes the entire case body down toward minimum chamber specs while letting you control exactly how much the neck gets worked using interchangeable bushings. That combination means you get cases that chamber smoothly in tight or semi-auto actions, plus the fine-tuned neck tension that drives real consistency downrange.
The small base part matters if you're feeding an AR-10, M1A, or any gas gun that's rough on brass. Standard full length dies work fine for a lot of rifles, but when fired brass gets a little fat at the base, rounds can drag or hang up on chambering. Sizing the body a few thousandths smaller gives the case room to spring back from the chamber walls so it extracts and feeds reliably, round after round. Plenty of reloaders also reach for a small base die when they're processing once-fired range pickups or military brass that was fired in a different, looser chamber.
What Sets the Type S Small Base Die Apart
The magic is in the bushing system. Rather than a fixed, one-size sizing button pulling through the neck, you choose a bushing in .001 inch increments to match your brass and the exact neck tension you want. The bushing floats and self-centers on the case neck, which helps keep your loaded rounds concentric and your bullets running true. You can measure your loaded neck diameter and subtract to find your bushing, or start a few thousandths under loaded outside diameter if your brass isn't neck turned.
Dialing In Your 308 Winchester Brass
The adjustable decapping rod lets you set bushing position so you can size only part of the neck when you want, and set your shoulder bump to match your chamber. Strip out the bushing and internal parts and the die even works as a body die. One tip worth repeating: because small base dies work the brass harder than standard dies, use good case lube generously to avoid stuck cases.
Key Specifications
- Manufacturer: Redding
- Manufacturer Part Number: 77355
- UPC: 611760773556
- Caliber: 308 Winchester
- Die Type: Small Base Type S Bushing Full Length Sizing Die
- Bushing System: Interchangeable bushings in .001 inch increments
- Bushings Included: No (sold separately)
- Shellholder Included: No (sold separately, uses Redding Shellholder #1)
- Bullet Diameter: 0.308 inch
- Thread: 7/8-14
- Number of Dies: 1
- Bushing Compatibility: Redding, Hornady, RCBS, and Wilson bushings
- Country of Origin: United States
What’s Included
- One Redding Type S Small Base Bushing Full Length Sizing Die
- Decapping rod assembly
- Standard sizing button
- Decapping pin retainer (for use in place of the button)
- Die box
- Instructions
Frequently Asked Questions
What's the difference between this small base die and a standard Type S full length die?
A small base die sizes the case body down a few thousandths smaller at the base than a standard full length die. That extra reduction gives fired brass room to spring back from the chamber walls so it chambers and extracts reliably. It's the die to reach for when standard sizing leaves your rounds dragging in a tight or semi-auto chamber.
Do I need bushings with the Type S Small Base Die, and are they included?
Bushings are not included and are sold separately. The die uses interchangeable steel bushings in .001 inch increments so you can match your brass and set your preferred neck tension. To pick a size, measure your loaded round's neck diameter and go about .001 inch under, or if your brass isn't neck turned, start .003 to .005 inch under the loaded outside diameter.
Is this die a good choice for reloading 308 for an AR-10 or M1A?
Yes, this is exactly where small base sizing shines. Gas guns like the AR-10 and M1A are hard on brass and can be picky about case dimensions, so small base sizing adds reliability insurance for feeding and extraction. Just remember that any semi-auto needs full length sizing every time, and this die handles that while still giving you bushing control over the neck.
Does the die come with a shellholder?
No, the shellholder is sold separately. For 308 Winchester, this die uses the Redding #1 shellholder. You'll also want quality case lube on hand, since small base dies work the brass harder and need good lubrication to prevent stuck cases.





Reviews
There are no reviews yet.