Description
Neck tension is one of those details that separates good ammo from great ammo, and this is where it starts. The Redding 73 Style Steel Bushing in .344 lets you size your case necks by exactly the amount you want, so your bullets are held with just the right grip. No more over-working the brass with a one-size-fits-all die. By picking the diameter that matches your loaded rounds, you get consistent seating and better case life out of your brass.
These bushings are machined from heat-treated steel, and the sizing diameters are hand-polished to a surface hardness of Rc 60-62. That hardness and polish do two things: they cut down on the effort it takes to run a case through the die, and they hold their dimension round after round. The standard external size is 1/2 inch outside diameter by 3/8 inch long, which is the footprint Redding uses across its bushing lineup. Each one is clearly marked with the size, so there's no guessing when you pull it off the shelf.
How the Redding .344 Steel Bushing Fits Your Setup
This .344 bushing freely interchanges in all Redding bushing-style neck sizing dies, including the Type S and Competition dies. It drops in without any fuss, which makes swapping diameters quick when you're load testing or working with a few different rifles. If you shoot more than one neck size, keeping a small range of these on hand covers a lot of ground.
Finding the Right Neck Bushing Diameter
Sizing is simple. Measure the outside neck diameter of a loaded cartridge with a good micrometer, then subtract about .001 inch to allow for brass springback and proper bullet tension. That gives you your bushing number. If you're running moly-coated bullets, you may want to go a touch smaller, around .001 to .002 inch under, to keep enough grip. Redding offers these in .001 inch increments across the full .185 to .368 inch range, so you can fine-tune to your exact chamber and brass.
Key Specifications
- Manufacturer: Redding
- Manufacturer Part Number: 73344
- UPC: 611760733444
- Bushing Diameter: .344 in
- Style: 73 Style Steel Neck Sizing Bushing
- Material: Heat-treated steel, hand-polished
- Surface Hardness: Rc 60-62
- External Dimensions: 1/2 in OD x 3/8 in long
- Available Range: .185 in thru .368 in in .001 in increments
- Quantity: 1 bushing
- Compatibility: All Redding bushing-style neck sizing dies
What’s Included
- One Redding 73 Style .344 steel neck sizing bushing
Frequently Asked Questions
Which dies does the Redding .344 steel bushing fit?
It freely interchanges in all Redding bushing-style neck sizing dies, including the Type S and Competition dies. The external dimensions are standard across Redding's bushing line at 1/2 inch outside diameter by 3/8 inch long, so it drops right in. You can swap diameters in and out without any extra fitting.
How do I know if .344 is the right bushing size for my load?
Measure the outside neck diameter of a loaded cartridge with a precision micrometer, then subtract about .001 inch to account for brass springback and bullet tension. If the result lands at .344, this is your bushing. For moly-coated bullets, you may want to go .001 to .002 inch smaller to keep enough neck grip.
What's the difference between the steel bushing and the titanium nitride version?
Both are heat-treated steel with hand-polished sizing diameters at Rc 60-62 hardness and the same external dimensions, so they interchange in the same dies. The titanium nitride bushings add a surface coating that further reduces sizing friction. The plain steel version like this .344 performs great and is the common go-to for most handloaders.
Will using the right neck bushing help my brass last longer?
Yes. Because you're sizing the neck by only the amount you need instead of over-working it the way a standard die can, you reduce the stress on the brass with each firing. That typically means more reloads per case and more consistent neck tension round to round.





Reviews
There are no reviews yet.