0
0

Redding Small Flash Hole Deburring Tool 06110 – .17 & .20 Cal

UPC: 611760061103

$34.99

1 in stock

Online inventory may differ from in-store availability. 

Fast Shipping

Quick turnaround so you get your gear sooner.

Secure FFL-Friendly Checkout

Trusted checkout with industry-standard protection.

Family-Owned Business

Keeping Traditions Alive Since 1953

Secure Transactions provided with

Description

When brass gets made at the factory, the flash hole is punched through from the outside, and that process can leave a little burr hanging on the inside web of the case. That burr sits right in the path of the primer flash, and it can throw off how evenly your powder lights from one round to the next. The Redding Small Flash Hole Deburring Tool is built to shave that burr off cleanly so ignition stays consistent. The nice part is you only have to do it once per case. Deburr a piece of brass today and it stays done for the life of that case.

What the Redding Small Flash Hole Tool Is Cut For

This is the small version, so it's dialed in specifically for .17 and .20 caliber cases and anything with a small .060" flash hole. Think .204 Ruger, .17 Hornet, 17 Remington, and similar small-bore brass. If you're working with standard .080" flash holes in .22 caliber and up, that's the job for Redding's Universal tool instead, so match the tool to your brass before you start.

Depth Control on the Small Flash Hole Deburring Tool

Unlike the Universal model, this small tool does not have a built-in shoulder stop, so the operator controls the cutting depth using the pilot stop. Because of that, it pays to trim your cases to a uniform length first so you get the same result across the whole batch. Setup is straightforward: install the pilot stop on the mandrel with the knurled end toward the handle, drop the cutter into an unprimed case until it reaches the flash hole, slide the pilot stop down to the case mouth, snug the setscrew, and turn clockwise to cut.

For precision reloaders chasing low ES and SD numbers, uniforming the flash hole is one of those brass prep steps that quietly earns its keep. It's a simple, one-time job that helps every round off that case meter a little cleaner off the primer.

Key Specifications

  • Manufacturer: Redding
  • Manufacturer Part Number: 06110
  • UPC: 611760061103
  • Flash Hole Size: .060" (small)
  • Caliber Range: .17 & .20 Cal
  • Mandrel Size: 9/64"
  • Included Pilot Stop: .22 Caliber
  • Depth Control: Operator controlled via pilot stop
  • Country of Origin: United States
  • Category: Case Preparation and Reloading Tools

What’s Included

  • Small flash hole deburring cutter
  • Accessory handle
  • .22 caliber pilot stop

Frequently Asked Questions

What calibers does the Redding Small Flash Hole Deburring Tool work with?

It's made for .17 and .20 caliber cases and any brass that uses a small .060" flash hole, such as the .204 Ruger and .17 Hornet. For standard .080" flash holes found in .22 caliber and larger cases, you'll want Redding's Universal tool instead. Matching the tool to your flash hole size is the key thing to get right.

Does this tool control the cutting depth on its own?

No, the small tool does not have a built-in depth stop like the Universal model does. The operator controls cutting depth using the pilot stop that rides against the case mouth. For the most consistent results, trim your cases to a uniform length before you start so every case cuts the same.

Do I have to deburr the flash hole every time I reload?

No, it's a one-time job. Once you deburr a piece of brass, it stays deburred for the life of that case. After the first pass you can set that case aside as prepped and never touch the flash hole again.

Why bother deburring the flash hole at all?

The burr left behind during manufacturing sits right where the primer flash travels, and it can cause uneven ignition from case to case. Removing it helps your powder light more consistently, which matters when you're chasing tight groups and low velocity spread. It's one of the quieter brass prep steps that precision reloaders lean on.

Additional information

UPC

611760061103

Manufacturer

Manufacturer Part Number

06110

Caliber/Gauge

Universal

Reviews

There are no reviews yet.

Be the first to review “Redding Small Flash Hole Deburring Tool 06110 – .17 & .20 Cal”