0
0

Forster Neck Reamer #284 (NR1284) .2865 Inside Neck Reamer

UPC: 757253004933

$31.99

2 in stock

Online inventory may differ from in-store availability. 

Fast Shipping

Quick turnaround so you get your gear sooner.

Secure FFL-Friendly Checkout

Trusted checkout with industry-standard protection.

Family-Owned Business

Keeping Traditions Alive Since 1953

Secure Transactions provided with

Description

Thick case necks are one of those quiet accuracy killers that a lot of reloaders overlook. When neck walls build up too much brass, they can crowd the chamber, spike pressure, and throw the occasional flyer that has you second-guessing your load. The Forster Neck Reamer #284 tackles that from the inside, trimming the interior neck walls of your .284 caliber brass so bullets seat clean and cases chamber the way they should.

This is the NR1284, sized to ream to .2865 inch for use with .284 diameter bullets. Like the rest of Forster's standard neck reamers, it's ground roughly .0025 to .003 inch over the maximum bullet diameter, which leaves just enough clearance for a proper fit without taking off more brass than you need. The cutter is machined from high grade, wear-resistant tool steel, so the edges hold up through hundreds of cases, and the staggered tooth design slices through brass smoothly instead of chattering its way down the neck.

How the Neck Reamer #284 Fits Your Setup

This reamer isn't a standalone tool and it isn't a pilot. It mounts in the cutter of a Forster Case Trimmer, dropping in where the pilot normally sits on the Original, Classic, and Power models. You run the case into the holder, line up the mouth, and turn the cutter assembly until the reamer passes completely through the neck. If you already run a Forster trimmer, adding the right caliber reamer is about the simplest upgrade you can make to your brass prep.

Getting the Most From the NR1284

Timing matters with inside neck reaming. Standard reamers like this one are meant to be used after the case has been fired with a full load and before you size the neck or run a full-length resize. A good rule of thumb that Forster itself passes along is to ream after firing and turn after sizing. Reaming works the brass flow that creeps up the neck on shouldered cases after a firing, so it's a natural fit for folks chasing tighter groups out of their .284 Winchester, 7mm wildcats, or other .284 bore rifles. Made in the USA by a company that's been building trusted reloading gear for decades.

Key Specifications

  • Manufacturer: Forster Products
  • Model: Neck Reamer #284
  • Manufacturer Part Number: NR1284
  • UPC: 757253004933
  • Caliber: .284 Caliber
  • Bullet Diameter: .284 inch
  • Reamer Diameter: .2865 inch
  • Material: High grade, wear-resistant tool steel
  • Tooth Design: Staggered tooth, chatter-free cut
  • Compatibility: Forster Original, Classic, and Power Case Trimmers
  • Mounting: Installs in trimmer cutter in place of the pilot
  • Country of Origin: USA
  • Quantity: 1 reamer

What’s Included

  • One Forster Neck Reamer #284 (NR1284) inside neck reamer

Frequently Asked Questions

What size does the Forster Neck Reamer #284 ream to?

The NR1284 reams to .2865 inch and is intended for use with .284 diameter bullets. Forster's standard neck reamers are ground about .0025 to .003 inch larger than the maximum bullet diameter, which leaves the correct clearance for a clean neck without removing excess brass.

Does the Neck Reamer #284 work on its own or do I need a trimmer?

It needs a Forster Case Trimmer. The reamer mounts in the cutter of the trimmer in place of the pilot, so it works with the Original, Classic, and Power models. It is not a standalone or hand tool.

When should I use the Forster Neck Reamer #284 in my reloading process?

Standard neck reamers are meant to be used after the case has been fired with a full load and before the neck or full-length sizing operation. A handy rule of thumb is to ream after firing and turn after sizing. This timing targets the brass flow that builds up the neck walls after a firing.

What calibers is this NR1284 reamer meant for?

This reamer is sized for .284 diameter bullets, which covers cartridges like the .284 Winchester and various 7mm builds that use a .284 bore. If your rifle or wildcat uses a different bullet diameter, Forster offers neck reamers in a range of other sizes.

Additional information

UPC

757253004933

Manufacturer

Manufacturer Part Number

NR1284

Caliber/Gauge

.284 Caliber

Shipping Weight

0.0188

Reviews

There are no reviews yet.

Be the first to review “Forster Neck Reamer #284 (NR1284) .2865 Inside Neck Reamer”