Description
Barnes built the Match Burner line to give competitive reloaders a seriously accurate bullet that doesn't drain the wallet, and the 6.5mm 140 grain is one of the most popular choices in the family. You get a lead-core, copper-jacketed hollow point boat tail measuring .264 in diameter with a G1 ballistic coefficient of 0.586 and a sectional density of 0.287. Overall length runs 1.341 inches, which seats nicely in a 6.5 Creedmoor case and plays well with the common 1:8 twist barrels you'll find on most modern 6.5 rifles.
What the Match Burner 140 gr Brings to the Loading Bench
This is a boat tail design, so you get that flatter trajectory and reduced wind drift that long-range work demands. Reloaders who weight-sort projectiles tend to like these because the weight spread out of the box is tight, which cuts down on the sorting work before you even get to the press. That consistency is a big part of why they earn their spot next to pricier match bullets.
Dialing In the 6.5 Match Burner for Your Rifle
If you've loaded 140 class 6.5 bullets before, you're already in the ballpark. H4350 is far and away the most common powder pairing, with plenty of folks landing accurate loads right around the low-to-mid 40s grain range depending on barrel length and chamber. IMR 4350, RL-16, and RL-17 all show up in Barnes published data too. Velocities in the high 2,700s to high 2,800s fps are realistic out of a 24 inch barrel, and the bullet stays supersonic well past 1,000 yards in the Creedmoor.
Where These 140 gr Bullets Earn Their Keep
Precision Rifle Series practice, 3-Gun, High Power, and ringing steel at distance are the bread and butter here. The Match Burner won't cost you anywhere near what boutique match bullets run, so they're easy to shoot in volume while you build and test loads. Pick up a 500 count box and you've got enough on hand to work up a load and still have plenty left to train with.
Key Specifications
- Manufacturer: Barnes
- Manufacturer Part Number: 31144
- UPC: 716876264056
- Caliber: 6.5mm / .264 Caliber
- Bullet Diameter: 0.264 in
- Bullet Weight: 140 grain
- Bullet Style: Hollow Point Boat Tail (HPBT)
- G1 Ballistic Coefficient: 0.586
- Sectional Density: 0.287
- Bullet Length: 1.341 in
- Core / Jacket: Lead core, copper jacket
- Cannelure: No
- Coating: Non-Coated
- Quantity: 500 per box
- Country of Origin: USA
What’s Included
- 500 Barnes Match Burner 6.5mm .264 140 grain HPBT bullets
Frequently Asked Questions
What powder works best with the Barnes Match Burner 6.5mm 140 grain?
H4350 is the standout pairing and shows up in both Barnes factory data and reloader results again and again, with accurate loads commonly landing in the low-to-mid 40s grain range depending on your barrel and chamber. IMR 4350, RL-16, and RL-17 are also listed in Barnes published data and give you room to experiment. Always start low and work up using current published load data for your specific setup.
Are these Match Burner bullets accurate enough for competition?
Yes, they were designed specifically for Precision Rifle, 3-Gun, and High Power competition. Many reloaders report sub-MOA groups once they dial in seating depth and charge, and the tight factory weight consistency is a real asset for those who weight-sort. They give you genuine match performance at a price that makes them easy to shoot in volume.
Will the 140 grain Match Burner stabilize in a standard 6.5 Creedmoor twist?
It will. These are a great fit for the common 1:8 twist barrels found on most modern 6.5 Creedmoor rifles, and the 1.341 inch length seats cleanly in a Creedmoor case. Shooters have reported good results across barrel lengths from short carbines up through 26 inch tubes.
What's the ballistic coefficient on this bullet?
The 6.5mm 140 grain Match Burner carries a G1 ballistic coefficient of 0.586 with a sectional density of 0.287. That BC keeps the bullet supersonic well past 1,000 yards in the 6.5 Creedmoor, which is a big reason the cartridge and this bullet get along so well for long-range work.





Reviews
There are no reviews yet.