Description
The 6mm Dasher built its reputation one tiny group at a time, and the RCBS Matchmaster Full-Length Bushing Die Set is made to keep that reputation intact round after round. This two-die set pairs a full-length bushing sizing die with the Matchmaster competition seating die, giving you the tools to size brass precisely and seat bullets with the kind of consistency that shows up on paper at 600 and 1,000 yards. For a wildcat that lives and dies by low runout and repeatable ignition, these dies are a natural fit.
The sizing die uses interchangeable neck bushings so you control exactly how much tension you put on the bullet. Swap bushings to tune neck tension to your brass and load, instead of being stuck with whatever a standard die hands you. To find the right bushing size, measure the outside neck diameter of a loaded cartridge and subtract about .002 to .003 inch to account for brass spring back. Keep in mind the bushings are sold separately, so you will want to grab the correct size for your setup. A titanium carbo nitride coated expander keeps case extraction smooth and cuts down on brass buildup, which helps reduce stretch at the neck over the life of your cases.
Why the Matchmaster Seating Die Earns Its Keep
The seating side is where this set really shines for precision work. A free floating, self centering seating stem keeps bullets aligned on the way down, and the bullet loading window with a retaining system lets you drop the bullet in and let the die handle the rest. Topping it off is a large, easy to read micrometer adjustment, so setting and repeating your cartridge overall length is quick and precise.
Built Like RCBS Reloading Gear Should Be
Each die is machined from case hardened steel, with the interior surfaces precision drilled, reamed, and hand polished. They use the standard 7/8-14 thread, so they drop right into your single stage or turret press, and they are backed by the RCBS limited lifetime warranty. For anyone running a 6 Dasher in PRS, NRL, or benchrest, this set gives you the control to make every case count.
Key Specifications
- Manufacturer: RCBS
- Caliber: 6mm Dasher
- Set Type: 2-Die Full-Length Bushing Set
- Included Dies: Full-Length Bushing Sizing Die, Matchmaster Competition Seating Die
- Neck Tension Control: Interchangeable Neck Bushings (sold separately)
- Expander: Titanium Carbo Nitride (TiCN) Coated
- Seater Adjustment: Micrometer Adjustable
- Seating Stem: Free-Floating, Self-Centering
- Material: Case-Hardened Steel
- Thread: 7/8-14
- Warranty: Limited Lifetime Warranty
- Manufacturer Part Number: 12308
- UPC: 604544653755
- Shipping Weight: 1.25 lbs
What’s Included
- Full-Length Bushing Sizing Die
- Matchmaster Competition Seating Die
- Decapping pin holder (non-expander piece)
Frequently Asked Questions
Do I need to buy neck bushings separately for this 6mm Dasher die set?
Yes. The sizing die is designed to run interchangeable neck bushings, but they are not included in the set. You will need to purchase the correct bushing for your brass before you can size cases.
How do I figure out which bushing size I need?
Measure the outside neck diameter of a loaded cartridge, then subtract about .002 to .003 inch to allow for brass spring back. That number gets you the bushing size that delivers your target neck tension. Having a couple of sizes on hand lets you fine tune as you develop a load.
Will the RCBS Matchmaster dies fit my press?
They use the industry standard 7/8-14 thread, so they thread right into virtually any single stage or turret press. If your press takes common dies, these will drop in without any trouble.
Is this set a good choice for PRS and benchrest loading?
Absolutely. The 6mm Dasher is a proven winner in both benchrest and Precision Rifle Series competition, and these dies are built for that level of precision. The bushing sizing, TiCN expander, and micrometer seater all work together to keep runout low and your loads consistent.




Reviews
There are no reviews yet.