Description
If you shoot a lot of .22 centerfire and want to take more control over your reloading, casting your own bullets is one of the most satisfying ways to do it. This RCBS mould (designation 22-055-SP) drops .225" nominal diameter, 55-grain soft point bullets, a weight and profile that sits right in the sweet spot for plinking, practice, and working up cast loads for your .22 centerfire rifles.
The double-cavity design means you pour two bullets per cast, which cuts your session time roughly in half once you get a good rhythm going at the pot. Each mould starts as a solid cast iron block that's precision ground square before any machining happens, so the two halves close up tight and stay that way. Steel alignment pins keep the blocks mated cleanly even after years of regular use, and the 3/16-inch solid steel sprue plate is held down with tempered steel spring washers and screws for a firm, repeatable cut every time you knock it open.
What the RCBS 22-055-SP Mould Drops
The finished bullet runs about 0.65 inches long with a roughly 0.46-inch nose, and it's designed to use a gas check on the base. That gas check helps protect the bullet base from hot gases and makes cast loads more forgiving at higher velocities, which is exactly what you want out of a fast little .22 cast bullet. If you want to size and lube after casting, the mould pairs with RCBS top punch #506.
Rounding Out Your RCBS Casting Setup
One thing worth knowing up front: this is the mould block and sprue plate only. The handles, sizer die, and top punch are sold separately, so if this is your first RCBS two-cavity mould you'll want to grab a set of handles to run it. Once you've got the handles and your casting pot sorted, this mould becomes a tool you'll reach for every time you want a fresh batch of .22 cast bullets without waiting on a store shelf to restock.
Key Specifications
- Manufacturer: RCBS
- Manufacturer Part Number: 82007
- UPC: 076683820075
- Designation: 22-055-SP
- Caliber: .22 Caliber
- Nominal Bullet Diameter: .225"
- Bullet Weight: 55 Grain
- Bullet Profile: Soft Point / Semi-Point
- Number of Cavities: Double (2)
- Gas Check: Required
- Top Punch: Uses RCBS #506
- Block Material: Solid Cast Iron, Precision Ground Square
- Sprue Plate: 3/16" Solid Steel
- Approx. Bullet Length: 0.65"
- Approx. Nose Length: 0.46"
What’s Included
- RCBS double-cavity bullet mould block (22-055-SP)
- Solid steel sprue plate
- Mounting hardware (spring washers and screws)
Frequently Asked Questions
Does the RCBS 22-055-SP mould come with handles?
No, the handles are not included and are sold separately. You'll need a set of RCBS two-cavity mould handles to run this block safely at the casting pot. If this is your first RCBS mould, plan to pick up a pair at the same time.
Do these cast bullets need a gas check?
Yes, this mould is designed to use a gas check on the bullet base. The gas check protects the base from hot powder gases and helps the cast bullet hold up at higher velocities, which matters with a fast .22 bullet. It's a small added step that pays off in accuracy and reduced leading.
What diameter and weight does the RCBS 22-055-SP drop?
It casts a .225" nominal diameter, 55-grain soft point bullet with the 22-055-SP designation. Finished bullets run roughly 0.65 inches long with about a 0.46-inch nose. Actual diameter and weight will vary slightly depending on your alloy, so size and weigh a few before loading.
What top punch works with this mould for sizing?
This mould pairs with RCBS top punch #506 when you size and lube your cast bullets. The sizer die and top punch are sold separately from the mould itself. Having the matching punch keeps the bullet nose centered and undamaged during sizing.




Reviews
There are no reviews yet.