Description
The RCBS 30701 is a Group A full-length two-die set cut for the .35 Whelen, and it covers everything you need to load this big-bore wildcat-turned-standard on a cartridge-by-cartridge basis. You get a full-length sizer die paired with an expander-decapping unit, plus a seater die with a bullet seater plug, so one box handles sizing, depriming, neck expansion, and bullet seating.
What the .35 Whelen Sizer Die Handles
The sizing die works the outside of the case back down to SAAMI minimum cartridge dimensions, which keeps your brass chambering smoothly after firing. The same pass deprimes the case and expands the neck so it's ready to accept a .358 bullet. RCBS vents this die to let trapped air and excess case lube escape, which is what keeps cases from getting dented or buckled during full-length sizing. Headspace is held to minimum tolerance so the body length stays put while the case gets worked.
Seating and Crimping in One Pass
The seater die runs a standard bullet seater plug and includes a built-in roll crimper. That lets you seat the bullet and roll crimp it into the cannelure at the same time, which is handy on a hard-recoiling round like the .35 Whelen where you want bullets locked in place in the magazine. If you'd rather seat and crimp separately, you can back the crimp out and run it in two steps.
Built With RCBS Die Steel and Standard Threads
These dies are machined from RCBS proprietary die steel and hardened for a long service life, so they'll outlast plenty of brass. They use the standard 7/8-14 thread, which means they thread right into any common single-stage or turret press without adapters. For anyone feeding a .35 Whelen on an Encore, a Remington 7600, or a custom bolt gun, this set gives you full control over your loads without hunting down hard-to-find factory ammo.
Key Specifications
- Manufacturer: RCBS
- Manufacturer Part Number (MPN): 30701
- UPC: 076683307019
- Caliber: .35 Whelen
- Product Type: Full-Length 2-Die Set
- Series: Group A (Popular Rifle Cartridges)
- Dies in Set: 2 (Full-Length Sizer, Seater)
- Thread: Standard 7/8-14 TPI
- Die Material: Proprietary RCBS die steel
- Sizing: Full-length to SAAMI minimum dimensions
- Seater Die: Bullet seater plug with built-in roll crimper
What’s Included
- Full-length sizer die with expander-decapping unit
- Seater die with bullet seater plug and built-in roll crimper
- RCBS green die box
Frequently Asked Questions
What comes in the RCBS .35 Whelen 2-die set?
The set includes a full-length sizer die with an expander-decapping unit and a seater die with a bullet seater plug. The sizer handles outside sizing, depriming, and neck expansion, while the seater takes care of bullet seating and crimping. It all ships in the familiar RCBS green die box.
Does the seater die crimp the bullet?
Yes. The seater die has a built-in roll crimper, so it can seat and roll crimp the bullet in the same stroke. You can also back the crimp out and run seating and crimping as separate steps if you prefer more control, which some loaders like for precision work.
Will this RCBS die set fit my reloading press?
It uses the standard 7/8-14 thread, so it threads directly into any common single-stage, turret, or progressive press without adapters. That covers the vast majority of presses from RCBS and other major brands. No extra hardware needed to get started.
Do I need a shell holder with the .35 Whelen die set?
Yes, a shell holder is sold separately and is not included with this die set. The .35 Whelen is based on the .30-06 case, so it uses the same shell holder as .30-06 and similar cartridges. Make sure you have the correct size on hand before you start loading.




Reviews
There are no reviews yet.