Description
When a round doesn't measure up or you want to salvage components from a loaded cartridge, this Forster #308 collet is the piece that does the gripping. It's sized for .308 diameter bullets, covering popular rounds like .308 Winchester, .30-06, .300 Blackout, 7.62×51 NATO, 7.62×39, and 7.62x54R, so it earns a spot in just about any .30 caliber reloader's kit. Unlike an inertia hammer puller, a collet-style setup clamps the bullet just above the case neck and draws it straight out, which keeps the powder in the case and the projectile intact for reuse.
What the Forster #308 Collet Is Built From
Forster machines this collet from solid steel, heat-treats it for long service life, and hand-polishes the gripping surface so it releases bullets smoothly instead of marring them. That attention to the working surface is a big part of why collet pullers earn repeat business on the bench. Once it's dialed in to the right tension, it grabs firmly enough to break the seal and pull the bullet without leaving a mark on the jacket.
Fitting the BP2308 to Your Press and Puller
This collet is a replacement or add-on piece, not a complete tool. It threads into Forster's collet-style bullet puller body, which in turn runs in any standard 7/8"-14 reloading press. It also fits both standard and universal bullet pullers, so if you already own a puller frame, you just swap collets as you move between calibers. Worth noting: the Forster bullet puller is not compatible with the Forster Co-Ax Press.
Getting the Most Out of It
Set it up once, snug the collet tension against a bullet seated just above the neck, and you've got a quiet, repeatable way to disassemble ammo without the pounding of an impact puller. Reloaders who pull more than a handful of rounds at a time tend to favor this method because it saves the brass, catches the powder, and lets you re-seat the same bullet if it's still good. For a .30 caliber bench, the #308 is one of the collets you'll reach for most.
Key Specifications
- Manufacturer: Forster Products
- Manufacturer Part Number: BP2308
- UPC: 757253003028
- Collet Number: #308
- Caliber: .30 Caliber
- Bullet Diameter: 0.308"
- Material: Solid steel, heat-treated
- Finish: Hand-polished gripping surface
- Compatibility: Standard and universal bullet pullers
- Press Fit: 7/8"-14 reloading press (via puller body)
- Shipping Weight: 0.024 lb
What’s Included
- One (1) Forster #308 bullet puller collet (.308 diameter)
Frequently Asked Questions
Does the Forster #308 collet come with the bullet puller tool?
No. This is just the .308 caliber collet itself. You'll need a Forster collet-style bullet puller body to use it, which then threads into your reloading press. If you already have the puller frame, you simply install this collet to handle .30 caliber bullets.
What cartridges does the #308 collet work with?
It fits any bullet with a .308 diameter, so it covers a wide range of .30 caliber loads including .308 Winchester, .30-06, .300 Blackout, 7.62×51 NATO, 7.62×39, and 7.62x54R. If your projectile measures .308 at the diameter, this collet is the right one.
Will the Forster #308 collet fit a universal bullet puller?
Yes. This collet is designed to fit both standard and universal bullet pullers, which gives you flexibility if you already own a puller body. Keep in mind the Forster bullet puller itself is not compatible with the Forster Co-Ax Press, so you'll want to run it in a conventional 7/8"-14 press.
Why use a collet puller instead of an inertia hammer puller?
A collet-style puller clamps the bullet and draws it straight out, which keeps the powder in the case and leaves the projectile and brass undamaged for reuse. It's quieter and more efficient than banging out rounds with an impact hammer, especially when you have a batch to pull. Once the tension is set correctly, it pulls bullets cleanly without marking the jacket.





Reviews
There are no reviews yet.