Description
Reloading fast is one of those skills that separates a smooth shooter from someone fumbling around under pressure, and a big part of that comes down to how forgiving your grip opening is. This magwell from Tyrant CNC bolts onto the bottom of a Glock 19 Gen 5 frame and flares the opening so your magazine has a much wider target to find, whether you're training in the dark, running a stage under a shot clock, or just trying to reload without staring at your hand.
What the Tyrant CNC Magwell Does for Your Reloads
The body is shaped with a calculated angle underneath that funnels the magazine up into the well instead of making you thread the needle. That angled geometry was worked out through testing rather than guesswork, and it shows the moment you start running drills. It also gives your support hand a little more surface to grip onto at the base of the pistol, which some shooters notice helps with control during recoil.
Build Quality Behind the Red Finish
This is a one-piece aluminum unit finished in red with a contrasting black screw, so there's nothing to lose track of during install. Tyrant CNC machines these parts in-house in Chicago and backs them with a lifetime warranty against defects, which says a lot about how confident they are in the anodizing holding up and the fitment staying tight over years of use. Installation is genuinely quick. You slide it over the base of the grip, line up the hole, and snug down the included screw with the wrench that comes in the box.
Fitment Notes for the Glock 19 Gen 5 Magwell
This version is cut specifically for the Glock 19 Gen 5 frame (it also lines up with the Glock 23 Gen 5 since they share the same lower geometry), so it won't interchange with Gen 3 or Gen 4 guns since Tyrant CNC machines those to a different frame profile. It plays nice with standard 15-round factory magazines and most aftermarket basepads and extensions, but it won't seat correctly with the factory reduced-capacity 10-round magazine or with backstrap inserts installed, so keep that in mind if either of those applies to your setup.
Key Specifications
- Manufacturer: Tyrant CNC
- Manufacturer Part Number: TDG19G5MWREDBLKSCREW
- UPC: 7426848614972
- Fitment: Glock 19 Gen 5 and Glock 23 Gen 5
- Material: CNC-machined aluminum
- Finish: Red anodized body with black screw
- Design: Flared funnel with angled underside for guided reloads
- Country of Origin: Made in USA (Chicago, IL)
- Warranty: Lifetime warranty against defects
- Magazine Compatibility: OEM 15-round mags and most aftermarket extensions/basepads
What’s Included
- Tyrant CNC red anodized aluminum magwell
- Black mounting screw
- Hex wrench for installation
Frequently Asked Questions
Will this magwell fit a Glock 19 Gen 3 or Gen 4?
No, this particular magwell is machined to match the Gen 5 frame geometry only. Tyrant CNC makes a separate version for Gen 3/4 Glock 19 and 23 pistols since the frame contours differ enough that the two aren't interchangeable.
Does the Tyrant CNC magwell work with the factory 10-round magazine?
It's not compatible with the OEM 10-round magazine that has a factory reduced-capacity base plate, and it also won't fit over a backstrap. Standard 15-round factory mags and most aftermarket basepads and extensions work fine with it.
Will this also fit a Glock 23 Gen 5?
Yes, the Glock 19 and Glock 23 Gen 5 share the same frame and magazine well dimensions, so this magwell fits both without any modification.
How long does installation take and what tools do I need?
Everything you need is in the box, including the mounting screw and a small wrench. Installation is a matter of sliding the magwell over the base of the grip, lining up the screw hole, and tightening it down, usually done in under a minute.





Reviews
There are no reviews yet.