Description
The ZULU-DMR Carbon Tripod Kit is SIG Sauer's answer to shooters and hunters who want a serious platform without lugging around dead weight. The three-section carbon fiber legs use vented tubes to stay stiff under load, which means less flex and a steadier hold whether you're building a prone position at the range or setting up on a rocky slope. It's the kind of tripod that earns its keep behind a precision rifle, a spotting scope, or even a camera.
What Sets the ZULU-DMR Carbon Kit Apart
Up top you get a 52mm dual-tension ball head that's ARCA-Swiss compatible, so it drops right into the gear most precision shooters already run. The dual-tension design lets you dial in resistance for smooth pans and repeatable adjustments, then lock down tight when you're ready to break a shot. With a 55-pound load rating, it handles heavy optics and rifles without complaint.
Dialing In the ZULU-DMR on Any Terrain
The legs run on rubber over-molded twist locks that open and close fast, even with gloves or in wet weather. Three-position detent tabs let you kick each leg out to different angles, so getting level on uneven ground or dropping down low for a prone shot is quick work. It stretches from a 30-inch minimum up to a 69-inch max height, covering everything from belly-to-the-dirt to a tall standing glassing setup.
Folded down, it measures 31.8 inches long and 5.9 inches wide, and the whole rig weighs about 6.4 pounds with the ball head attached. That's light enough to strap to a pack for backcountry hunts but stout enough for match day. Built to the same standards SIG applies to its weapon systems, the ZULU-DMR is one of those pieces of kit you set up once and stop thinking about.
Key Specifications
- Model: ZULU-DMR
- Manufacturer: SIG Sauer Electro-Optics
- Manufacturer Part Number: SOZT1002
- UPC: 798681681280
- Color: Flat Dark Earth (FDE)
- Leg Material: Carbon Fiber, 3-Section with Vented Tubes
- Ball Head: 52mm Dual Tension
- Mounting Interface: ARCA-Swiss Compatible
- Leg Angle Positions: 3-Position Detent Tabs
- Leg Locks: Rubber Over-Molded Twist Locks
- Max Load: 55 lbs
- Min Height: 30 in
- Max Height: 69 in
- Folded Dimensions (H x W): 31.8 in x 5.9 in
- Weight: 6.4 lbs with ball head
- Warranty: SIG Sauer Infinite Guarantee / Limited Lifetime
What’s Included
- ZULU-DMR carbon fiber tripod with 52mm dual-tension ball head
- ARCA-Swiss base plate
- Allen wrenches (5mm and 2.5mm)
- Carry case
- Operator's manual
Frequently Asked Questions
Will the ZULU-DMR tripod work with my existing ARCA-Swiss gear?
Yes. The 52mm dual-tension ball head is ARCA-Swiss compatible, so any ARCA rail or clamp you already run should drop right in. It comes with an ARCA-Swiss base plate as well, making it easy to swap between a rifle, spotting scope, or camera.
How much weight can the ZULU-DMR carbon tripod hold?
It's rated for up to 55 pounds of load, which comfortably covers precision rifles, heavy spotting scopes, and camera setups. That headroom means it stays rock steady even with a fully built-out rig on top.
How tall does the tripod get, and can it go low for prone shooting?
The ZULU-DMR extends from a 30-inch minimum up to 69 inches at full height. The three-position detent tabs let you splay the legs wide to drop down for prone work or level out on uneven ground, so it adapts to whatever position you're shooting from.
Is the ZULU-DMR light enough to pack for backcountry hunts?
It weighs about 6.4 pounds with the ball head attached and folds down to 31.8 inches, so it straps to a pack without weighing you down. The carbon fiber legs keep it light while still holding up under heavy loads in the field.





Reviews
There are no reviews yet.