Description
There is something special about a .410 over under, and the Browning Citori 725 Field in .410 bore with 26 inch barrels is one of the nicest ways to get into one. The 725 traces its lineage back to John Browning's B25 Superposed, but the receiver sits noticeably lower than older Citori designs. That puts your eye closer to the bore line, so the gun points more naturally and comes back straight into your shoulder instead of hopping at the muzzle. On a fast quail flush or a crossing clay, that low-slung balance is the difference between chasing the bird and being on it.
Citori 725 Field Build Quality
The receiver is steel with a silver nitride finish and high relief engraving, paired against polished blued barrels and a Grade II/III black walnut stock with a gloss oil finish. Grain on these tends to run well above what you see on most field guns in the case. Underneath the good looks is the same proven Citori architecture: a full width hinge pin, a tapered locking bolt that engages the rear barrel lugs, and action parts hand fitted the old fashioned way. These guns have a long reputation for digesting decades of shells without going loose.
Shooting the 725 Field .410
The FireLite mechanical trigger gives you a light, crisp break on both barrels without relying on recoil to set the second sear, which matters with soft-shooting .410 loads. Chambers are 3 inch and chrome plated, Vector Pro lengthened forcing cones help keep patterns even, and an ivory bead up front sits on the vent rib for a clean sight picture. The Inflex recoil pad is mostly along for the ride in this bore, but it mounts smoothly and stays put on your shoulder. At around 7 pounds with a 43.75 inch overall length, it carries all day and swings smooth.
Browning includes Full, Modified, and Improved Cylinder flush choke tubes, so you are covered from tight patterns on late season birds to open spreads over pointing dogs. Whether this becomes your grouse gun, a skeet toy, or the one your grandkids fight over someday, the 725 Field in .410 earns its keep.
Key Specifications
- Manufacturer Part Number: 018165914
- UPC: 023614736714
- Gauge/Bore: .410 Bore
- Action: Over/Under, Break Open
- Barrel Length: 26" Vent Rib
- Chamber: 3" Chrome-Plated
- Capacity: 2 Rounds
- Chokes Included: Full, Modified, Improved Cylinder
- Trigger: FireLite Mechanical
- Receiver Finish: Silver Nitride with Engraving
- Barrel Finish: Polished Blued
- Stock: Grade II/III Black Walnut, Gloss Oil Finish
- Recoil Pad: Inflex
- Front Sight: Ivory Bead
- Safety: Tang-Mounted
- Overall Length: 43.75"
What’s Included
- Browning Citori 725 Field .410 bore over/under shotgun
- Three flush choke tubes (Full, Modified, Improved Cylinder)
- Choke tube wrench
- Owner's manual
- Locking device
Frequently Asked Questions
What choke tubes does the Citori 725 Field .410 come with?
This model ships with three flush-fit choke tubes: Full, Modified, and Improved Cylinder. That trio covers most upland hunting and clay work right out of the box. Note that the .410 and 28 gauge 725 models use Browning's standard flush Invector tubes rather than the Invector-DS system found on the 12 and 20 gauge versions, so keep that in mind if you shop for extra chokes.
Is a mechanical trigger better than an inertia trigger on an over under?
For a .410, yes it matters. An inertia trigger relies on recoil from the first shot to set up the second barrel, and light .410 loads sometimes do not generate enough push to do that reliably. The FireLite mechanical trigger in the 725 fires the second barrel regardless of recoil, and it breaks lighter and cleaner than most traditional Citori triggers.
How heavy is the Browning Citori 725 Field in .410 with 26 inch barrels?
It runs right around 7 pounds, which is a nice middle ground for a small bore over under. It is light enough to carry through a long day of upland hunting, but there is enough weight between the hands to keep your swing smooth on clays. Overall length is 43.75 inches with the 26 inch barrels.
Can the 725 Field .410 shoot both 2.5 inch and 3 inch shells?
Yes. The chambers are 3 inch and chrome plated, so they will handle 3 inch magnum loads as well as the shorter 2.5 inch shells. Since it is a break action with extractors and a mechanical trigger, there are no cycling concerns with lighter loads like you would have in a semi-auto.





Reviews
There are no reviews yet.