Description
Follow-up shots get a lot easier when the muzzle isn't jumping all over the place, and that's exactly what the Ruger Radial Port Muzzle Brake is built to fix. The radial port layout vents gas outward in a full circle to cut down felt recoil and keep muzzle movement to a minimum, which means your dot or crosshair settles back on target faster. It's a genuine Ruger factory part machined right here in the USA by Swan Manufacturing, so fit and finish match what you'd expect off a factory rifle.
What Makes the Radial Port Design Different
Because the ports are cut radially around the body, this brake doesn't need to be timed like a lot of ported comps and brakes on the market. That's a real time saver on installation. There's no crush washer or jam nut to fuss with. You thread it onto a 1/2"-28 barrel, snug it down with an 11/16" open-end or crescent wrench, and torque it to 15 to 20 ft-lbs. That's the whole job.
Fit and Build on the Ruger Radial Port Brake
This one is spec'd for .223 Rem and 5.56 NATO barrels, and it's a natural match for the AR-556 and similar 1/2"-28 threaded rifles. It also plays nicely with other .224-bore rifles running the same thread pitch, so bolt guns like a 22-250 or a Ruger American in the right chambering can take it too. The body is alloy steel with a black oxide finish that blends in with most black rifles without drawing attention. It runs about 1-3/4 inches long, three-quarters of an inch in diameter, and tips the scale at roughly 1.7 ounces, so it won't throw off the balance up front.
If you've been running a bare thread or a plain flash hider and want to knock down recoil without breaking out a specialty tool, this is about as simple as an upgrade gets. Factory Ruger quality, no timing headaches, and a noticeable difference in how flat the rifle shoots.
Key Specifications
- Manufacturer: Ruger / Sturm, Ruger & Co.
- Model: Radial Port Muzzle Brake
- Manufacturer Part Number: 90486
- UPC: 736676904860
- Caliber: .223 Rem / 5.56 NATO
- Thread Pattern: 1/2"-28 tpi
- Material: Alloy Steel
- Finish: Black Oxide
- Color: Black
- Length: 1-3/4 in
- Diameter: .75 in
- Weight: 1.7 oz
- Install Torque: 15-20 ft-lbs
- Timing Required: No
- Country of Origin: Made in USA (Swan Manufacturing)
What’s Included
- Ruger Radial Port Muzzle Brake (1)
Frequently Asked Questions
Does the Ruger Radial Port Muzzle Brake need to be timed or use a crush washer?
No timing is required, which is one of the nicest things about the radial port design. You don't need a crush washer or jam nut either. Just thread it on and torque it to 15 to 20 ft-lbs with an 11/16" wrench.
What rifles will this Radial Port brake fit?
It's made for .223 Rem and 5.56 NATO barrels with 1/2"-28 muzzle threads, so it's a direct match for the Ruger AR-556 and similar ARs. It also works on other .224-bore rifles running the same thread pitch, including bolt guns like the 22-250. Just confirm your muzzle is threaded 1/2"-28 before ordering.
What tools do I need to install the Ruger Radial Port Muzzle Brake?
An 11/16" open-end or crescent wrench is all you need to snug it down. A torque wrench helps you hit the 15 to 20 ft-lb spec cleanly. Since there's no timing involved, installation takes just a couple of minutes.
Is this a genuine Ruger factory part?
Yes, it's an authentic Ruger factory muzzle device carrying part number 90486. It's machined in the USA by Swan Manufacturing to Ruger's specs. The alloy steel body wears a black oxide finish that matches most factory black rifles.






Reviews
There are no reviews yet.