Description
The Magpul XTM Hand Stop Kit is one of those small upgrades that pays off every time you pick up your rifle. Instead of guessing where your support hand lands, you get a positive forward stop that indexes your grip in the exact same place run after run. It also keeps your fingers from creeping up toward a hot front sight assembly or muzzle, which matters more than you'd think during longer range sessions or fast strings of fire. This is the OD Green version, built from lightweight reinforced polymer with Magpul's aggressive TSP texture for a sure hold.
What Comes in the XTM Hand Stop Kit
This is a four-piece set, so you're not just getting a single stop. Inside you'll find one hand stop, one index panel, one full XTM enhanced panel, and one XTM enhanced half panel. That mix lets you build the layout that fits your hands and your handguard rather than being stuck with one setup. The panels double as rail covers too, so any exposed Picatinny slots around the stop get protected from dings and stay comfortable against your palm.
Getting the XTM Hand Stop on Your Rail
Installation is about as simple as it gets. The kit uses the same interlocking tab system found on Magpul's XTM Rail Covers and clamps down with a 1/8 inch hex tool, so you can have it mounted and dialed in without a trip to the workbench. It fits standard 1913 Picatinny rails and works on AR15, M4, and M16 platforms, and the ambidextrous design means lefties and righties both get the same setup.
Weight is barely a factor here. The hand stop itself runs right around three quarters of an ounce, and the panels are even lighter, so you get real-world control without loading down the front of your rifle. It's a popular swap for folks moving away from an angled foregrip who want something slimmer that still gives the hand a place to settle. Made in the USA, it carries the same reputation for toughness Magpul gear is known for.
Key Specifications
- Manufacturer: Magpul Industries
- Manufacturer Part Number: MAG511-ODG
- UPC: 873750007816
- Model: XTM
- Color: OD Green
- Material: Reinforced Polymer
- Mount Type: 1913 Picatinny Rail
- Firearm Fit: AR15 / M4 / M16
- Hand Orientation: Ambidextrous
- Texture: TSP
- Hand Stop Weight: 0.74 oz
- Index Panel Weight: 0.39 oz
- Full Enhanced Panel Weight: 0.28 oz
- Half Enhanced Panel Weight: 0.14 oz
- Install Tool: 1/8 inch hex
- Country of Origin: Made in USA
What’s Included
- 1 Magpul XTM Hand Stop
- 1 XTM Index Panel
- 1 Full XTM Enhanced Panel
- 1 XTM Enhanced Half Panel
Frequently Asked Questions
What kind of rail does the XTM Hand Stop Kit fit?
It's built for standard 1913 Picatinny rails and mounts using the same interlocking tab system as Magpul's XTM Rail Covers. It works across AR15, M4, and M16 platforms as long as you have Picatinny slots to clamp onto. If your handguard is M-LOK or KeyMod only, you'd need Picatinny rail sections first.
Do I need special tools to install the Magpul XTM Hand Stop Kit?
Just a 1/8 inch hex tool, which is all it takes to clamp the pieces down onto your rail. The install is quick and doesn't require any gunsmithing or permanent modifications. You can reposition or reconfigure the panels anytime you want to fine-tune your grip.
What's the difference between the hand stop and the panels in the kit?
The hand stop is the raised piece that gives your support hand a positive place to index and stops it from sliding forward toward the muzzle. The index panel, full enhanced panel, and half enhanced panel are textured rail covers that surround the stop for grip and rail protection. Having all four lets you set up the exact layout that suits your hand position.
Is the XTM Hand Stop a good replacement for an angled foregrip?
A lot of folks make exactly that swap. The XTM keeps a much lower profile than an AFG while still giving your hand a reference point and forward stop, so you get control without the added bulk. It's a solid pick if you prefer a slimmer, snag-free front end.







Reviews
There are no reviews yet.