Description
There is nothing more annoying than torquing down a muzzle brake and watching the ports stop thirty degrees short of level. Crush washers are a guessing game, and peel washers get fiddly fast. Shims are the clean solution, and this Rugged Suppressors SA017 kit is purpose-built for .338 caliber setups running 3/4×24, M18x1, or M18x1.5 barrel threads. You stack the right combination behind your brake or flash hider, torque it down, and the device lands exactly where you want it every time.
Why the Rugged SA017 Shim Kit Earns a Spot in Your Range Bag
The kit comes with three shim sizes, which is what lets you dial in your timing so precisely. Mix and match thicknesses until the math works out, then tighten to spec and you are done. The shims measure .760 inch inside diameter and .875 inch outside diameter, so they seat properly on big-bore thread shoulders without hanging over the edge or rattling loose. Everything is finished in Black Nitride, which shrugs off heat and corrosion at the muzzle where things get hot and dirty, and the whole kit is made in the USA.
Proper Alignment Matters More With a Can Attached
If you are running a Rugged suppressor on a brake-mount system, correct indexing is not just about looks. A properly timed and torqued muzzle device gives your suppressor a square, consistent mounting surface, which is exactly what you want when a baffle stack is hanging off the end of your barrel. Worth noting that Rugged ships shims with their .338 three-port brakes from the factory, so this kit is mainly for anyone who lost their originals, bought a brake secondhand, or needs extra thicknesses to fine-tune a new barrel. It weighs next to nothing, costs less than a box of match ammo, and saves you a ton of frustration at install time. Keep one in the parts drawer and thank yourself later.
Key Specifications
- Manufacturer: Rugged Suppressors
- Manufacturer Part Number: SA017
- UPC: 850044499199
- Model: Shim Kit
- Caliber: .338 Cal (8.6mm bore devices)
- Thread Compatibility: 3/4×24, M18x1, M18x1.5
- Inner Diameter: .760 in
- Outer Diameter: .875 in
- Shim Sizes Included: 3
- Finish: Black Nitride
- Product Type: Silencer Accessory
- Made In: USA
What’s Included
- Three sizes of precision alignment shims in a bag
Frequently Asked Questions
What thread pitches does the Rugged SA017 shim kit work with?
This kit is sized for .338 caliber barrel threads in 3/4×24, M18x1, and M18x1.5. The shims measure .760 inch inside diameter and .875 inch outside diameter, so they seat cleanly on the thread shoulder of big-bore barrels. If you are running a 5/8×24 or 1/2×28 barrel, Rugged makes separate shim kits for those thread pitches.
Why use shims instead of a crush washer to time my muzzle brake?
Shims give you a repeatable, solid mounting surface, while crush washers deform unpredictably and can let a device shift under heavy use. That matters even more with a suppressor mounted on the brake, since you want the device torqued square and consistent. Stack shims until the brake times correctly at your torque spec and it will land in the same spot every time you reinstall it.
Do Rugged .338 muzzle brakes already come with shims?
Yes, Rugged includes shims with their .338 three-port brakes from the factory. This SA017 kit is the move if you misplaced your originals, picked up a brake secondhand, or swapped to a new barrel and need different thicknesses to get the timing right.
How do I figure out which shims to use?
Hand-tighten your brake and note how far past top dead center it stops, then add shims until the device reaches proper alignment at full torque. It usually takes a little trial and error with different combinations of the three thicknesses. Once you find the right stack, write it down so reinstalls after cleaning are quick.





Reviews
There are no reviews yet.