Description
The MDT 1" Medium Scope Rings are built for people who want their optic to go on straight, stay put, and never give them a reason to second-guess their zero. These are 1-inch rings in a medium 1.00" height, machined from a solid billet of 6061 aluminum and CMM checked to 1.5 millionths of an inch. That kind of tolerance is why MDT says no lapping is required, and in practice the rings seat clean and align your scope right the first time.
What sets the Premier line apart is the STANAG 4694 clamping design, better known as NATO spec. Instead of leaving a gap between the rail and the ring like a lot of standard mounts, the Premier rings sit tight on top of the rail with pressure spread across the angled surfaces underneath. That gives you more contact and a more solid interface, and it means these will clamp down on both STANAG and MIL-STD-1913 rails, even ones that run slightly out of spec.
Why the MDT Premier Rings Hold Zero
Each ring uses four oversized #8-32 Grade 8 fasteners to clamp the scope, so the clamping force gets distributed evenly and your optic isn't going to shift or rotate under recoil. The rings are machined in matched pairs for a precise fit, and the stepped base-to-cap interface is a nice touch. It lets you snug down the fasteners on one side before making your final scope alignment, which takes the guesswork out of keeping your gaps even.
Mounting the 1" Medium Scope Rings
At roughly 2 ounces per ring, these keep weight off your build without feeling flimsy. The medium 1.00" height gives most standard-objective scopes enough clearance over the barrel while keeping the optic low enough for a comfortable cheek weld. MDT lists ring cap torque around 15 to 22 inch-pounds and the rail clamp screws at 25 to 30 inch-pounds, so grab a torque wrench and you'll have them dialed in a few minutes. Whether the rifle sees hunting season, range days, or match duty, these rings are a dependable foundation for your glass.
Key Specifications
- Manufacturer: MDT
- Manufacturer Part Number: 103343-BLK
- UPC: 990482717803
- Scope Tube Diameter: 1 inch (1.00")
- Ring Height: Medium (1.00")
- Material: Billet 6061 Aluminum
- Finish: Matte Black
- Attachment Type: Picatinny / STANAG 4694 NATO Spec
- Fasteners: Four oversized #8-32 Grade 8 per ring
- Precision: CMM checked to 1.5 millionths of an inch
- Weight: Approx. 2 oz per ring (4 oz per set)
- Ring Cap Torque: 15 to 22 in-lbs
- Rail Clamp Torque: 25 to 30 in-lbs
What’s Included
- Two (2) MDT Premier 1" Medium scope rings (matched pair)
- Mounting hardware (four #8-32 Grade 8 fasteners per ring)
Frequently Asked Questions
Will the MDT Premier 1" Medium rings fit a Picatinny rail?
Yes. These rings are built to the STANAG 4694 NATO spec and clamp directly to Picatinny and MIL-STD-1913 rails. The design also lets them seat securely on rails that run slightly out of spec, so you get a solid interface across most standard bases.
Do I need to lap these scope rings before mounting?
No lapping is required. MDT machines the Premier rings in matched pairs and CMM checks them to 1.5 millionths of an inch, so they seat and align the optic accurately right out of the package. That saves you time and a potential headache during install.
What height is "medium" and will it clear my barrel?
Medium height on these rings is 1.00", measured from where the ring meets the base to the centerline of the scope. That height clears most standard-objective 1-inch scopes while keeping the optic low enough for a natural cheek weld. For larger objective bells you may want to step up to a higher ring.
What are the torque specs for the MDT Premier rings?
MDT recommends roughly 15 to 22 inch-pounds on the ring cap screws and 25 to 30 inch-pounds on the rail clamp screws. Make sure the ring is firmly seated against the rail before torquing, and always defer to your scope maker's final value for the cap screws to avoid over-clamping the tube.




Reviews
There are no reviews yet.