Description
The Midwest Industries MI-1022-8H is a drop-in upgrade for the Ruger 10/22 Takedown that swaps the factory plastic forend for a real free-float tube. Machined from 6061 aluminum and finished in Type III hard coat anodizing, it runs 8 inches in a slim profile that keeps things light while opening up real estate for accessories. The whole thing comes dehorned, so there are no sharp edges digging into your support hand during a long range session.
What the MI-1022-8H Brings to Your Takedown
This is a true free-float design, meaning nothing touches the barrel but the mounting point, which is good news for consistency downrange. You get eight sides of M-LOK slots running the length of the handguard, giving you plenty of spots for a light, laser, bipod, or hand stop. Two anti-rotation QD sockets are built right in for push-button sling swivels, and a 5-slot polymer M-LOK rail ships in the box if you want a short section of Picatinny for an optic or front sight. Weight comes in right around 7 ounces installed, so it won't throw off the balance that makes the Takedown so handy to carry.
Fitting the 8" Handguard to Your Rifle
Installation is straightforward with the included mounting bolt and wrench, and most folks have it buttoned up in a few minutes. Keep in mind this is sized for the newer Ruger 10/22 Takedown models, and the 8-inch length also plays nicely with the 22 Charger pistol if you've got one of those in the safe. Because the Takedown is a two-piece gun by nature, a little patience during alignment goes a long way. Starting by lining the handguard up with the top edges of the factory stock tends to give the cleanest result.
Built to Last on the MI-1022-8H
Midwest Industries has a long track record making solid AR and rimfire parts, and this handguard carries their lifetime warranty. The hardcoat anodizing shrugs off the usual range wear, and the aluminum construction means it'll outlast the plastic piece it replaces without adding much heft. For anyone building out a trail gun, a plinker, or a scaled-down tactical setup, it's a clean foundation to build on.
Key Specifications
- Manufacturer: Midwest Industries
- MPN: MI-1022-8H
- UPC: 812102032632
- Fits: Ruger 10/22 Takedown (new models) / 22 Charger
- Length: 8 inches
- Material: 6061 Aluminum
- Finish: Type III Hard Coat Anodized, Black
- Mounting System: M-LOK (8 sides)
- Design: True Free Float
- QD Sockets: Two built-in anti-rotation
- Inside Diameter: 1.190 inches
- Weight: Approx. 7.3 oz installed
- Warranty: Midwest Industries Lifetime
What’s Included
- 8" M-LOK handguard
- 5-slot polymer M-LOK rail section
- Mounting bolt
- Installation wrench
Frequently Asked Questions
Will this handguard fit my Ruger 10/22 Takedown?
It's made specifically for the newer Ruger 10/22 Takedown models and installs in place of the factory forend. The 8-inch version also works well on the 22 Charger Takedown pistol. It is not designed for the standard non-takedown 10/22.
Is the MI-1022-8H a true free-float handguard?
Yes. It uses a true free-float design, so the tube mounts at a single point and does not contact the barrel along its length. That setup helps keep your barrel harmonics consistent for better accuracy.
What accessories can I mount on the 8" handguard?
It has eight sides of M-LOK slots, so you can add M-LOK lights, lasers, bipods, hand stops, and sling mounts wherever you need them. Two built-in QD sockets handle push-button sling swivels, and the included 5-slot polymer rail gives you a short Picatinny section for an optic or front sight.
How hard is it to install?
Most people find it a straightforward job using the included mounting bolt and wrench. Since the Takedown is a two-piece rifle, take your time with alignment, and lining the handguard up with the top edges of the factory stock usually gives the best fit. On some rifles you may need to remove the factory rear sight to clear the handguard.




Reviews
There are no reviews yet.