Description
The Cthulhu Lower takes the weakest link on a Ruger Mark IV or 22/45, the factory polymer grip frame, and replaces it with a machined aluminum unit that shows up fully built out with TandemKross parts. What used to be a stripped lower that needed a pile of parts and a few hours at the bench is now a complete grip frame that hosts your pistol's upper right out of the box. It packs in well over 30 parts, components, and accessories, all installed, assembled, and test fit at the shop before it ships.
This particular version is the green frame with black accessories, and since only the upper on a Mark IV is the serialized part, the lower is not serialized and ships like any other component. It works with virtually any factory or aftermarket Mark IV or 22/45 upper, which also means you can take a Standard Mark IV and turn it into a 22/45 by swapping to 22/45 magazine base pads.
What the Cthulhu Lower Brings to the Table
Ergonomics are where you feel the difference first. The frame has an enlarged, hooked trigger guard that gives big or gloved hands room to work and adds another point of contact, plus a textured backstrap that locks the pistol into your hand. The hiveGrip panels carry a hexagonal texture that looks sharp and grips well. On the controls side you get a Victory trigger with a crisp, light break, the Titan extended magazine release, a Bolt Keeper extended bolt stop, and both the Cornerstone safety thumb ledge and Accelerator forward thumb ledge for your support hand.
Built for the Range and the Clock
One thing to know going in: the factory one-button takedown is replaced by a single takedown screw. You lose the push-button, but you gain a noticeably tighter fit between upper and lower with far less play, which steel challenge and rimfire competitors tend to appreciate. The Cerakoted aluminum also shrugs off heat, chemicals, and the kind of wear that beats up a polymer frame over thousands of rounds. Whether you are building a dedicated steel gun or just want your plinker to feel like a custom piece, this is about as turnkey as a Mark IV grip frame upgrade gets.
Key Specifications
- Manufacturer: TandemKross
- Manufacturer Part Number: TK26N0461GBY1
- UPC: 657768397707
- Color: Green Frame / Black Accessories
- Material: CNC-machined aluminum, Cerakote finish
- Compatibility: Ruger Mark IV Standard and Mark IV 22/45 uppers (factory or aftermarket)
- Assembly: Fully assembled and test fit, drop-in ready
- Takedown: Single takedown screw (replaces factory one-button)
- Serialized: No, lower is a non-serialized component
- Trigger: Victory flat-faced trigger
- Magazine Release: Titan extended magazine release
What’s Included
- Cthulhu aluminum grip frame (green)
- Victory trigger (black)
- hiveGrip panels
- Titan extended magazine release
- Bolt Keeper extended bolt stop
- Cornerstone safety thumb ledge
- Accelerator forward thumb ledge for Mark IV 22/45
- Blast Pack
- Engraved titanium grip screws (4-pack)
Frequently Asked Questions
Does the Cthulhu Lower come assembled or do I have to build it?
It comes fully assembled and test fit with all the TandemKross internals and controls already installed. You just mount your existing Mark IV or 22/45 upper onto it and you are ready to shoot. There is no bench work or parts sourcing needed on your end.
Will this lower work with my Ruger Mark IV upper?
Yes. Because every Mark IV Standard and 22/45 shares the same one-button takedown setup, the Cthulhu Lower accepts virtually any factory or aftermarket Mark IV or 22/45 upper. That also lets you turn a Standard Mark IV into a 22/45 feel by swapping to 22/45 magazine base pads.
Why does the Cthulhu Lower use a takedown screw instead of the factory button?
The single takedown screw replaces the push-button to tighten up the fit between the upper and lower, cutting down on play for a more solid lockup. You will need an Allen wrench to break it down rather than just pressing a button. Competitors chasing consistent point of impact tend to see that tradeoff as a win.
Is the Cthulhu Lower really an upgrade over the stock polymer frame?
The machined aluminum frame is stronger and holds tighter tolerances than the factory plastic, and the Cerakote finish stands up better to heat, chemicals, and general wear. On top of that you get a crisp Victory trigger, extended controls, thumb ledges, and the textured hiveGrip, all of which make the pistol feel and shoot like a custom build.




Reviews
There are no reviews yet.