Description
The CMC 92702 is a match-grade two stage trigger built for AR-15 and AR-10 rifles, and it's one of the easiest upgrades you can make to a rifle that came with a rough factory trigger. You get a light 2-pound first stage that leads into a crisp 2-pound second stage break, so there's a defined wall and a clean release you can count on shot after shot. The flat trigger bow gives your finger more surface to rest against, which helps you find the same spot every single pull.
What Makes the CMC 92702 Different
Unlike traditional fire control groups that have you fussing with loose springs, a hammer, and a disconnector, this whole assembly is self-contained inside an 8620 alloy steel housing. That housing also keeps carbon, grit, and debris out of the internals, which is a nice bonus for reliability over the long haul. Inside, a lightened hammer paired with a full-power Rocket Wire spring keeps lock time short while still hitting hard enough to reliably light off both commercial and surplus ammo.
Dropping the CMC 92702 Into Your Build
Installation is about as painless as it gets. Knock out your mil-spec trigger pins, set the unit into the lower, reinstall the pins, and snug the pinset screws. Most folks have it done in a few minutes with basic tools and no gunsmithing. This is the small pin version, sized for a .154 inch pin hole, which covers just about every AR out there except older Colt rifles built between 1991 and late 2009 that use the larger .172 inch pin.
Where the CMC 92702 Shines
The short reset and light, consistent pull make this a great match for precision work, target shooting, hunting, and general range use where a better trigger genuinely tightens up your groups. The pull weight is factory preset and not adjustable, which keeps the feel repeatable and takes the guesswork out of it. CMC has been making the original drop-in AR trigger out of Texas for years, and this two stage remains a favorite for people who want serious feel without a lot of fuss.
Key Specifications
- Manufacturer: CMC Triggers
- Manufacturer Part Number: 92702
- UPC: 810943031401
- Trigger Type: Two Stage, Drop-In
- First Stage (Set): 2 lb
- Second Stage (Release): 2 lb
- Trigger Bow: Flat
- Pin Size: Small Pin (.154 inch)
- Housing Material: 8620 Alloy Steel
- Adjustability: Factory Preset, Non-Adjustable
- Fitment: AR-15 / AR-10 / LR-308
- Country of Origin: USA (Texas)
What’s Included
- CMC 92702 self-contained two stage trigger assembly
- Mil-spec trigger and hammer pins
- Pinset screws
Frequently Asked Questions
Will the CMC 92702 fit my AR-15 or AR-10?
This is the small pin version, built for receivers with a .154 inch trigger and hammer pin hole, which covers the large majority of AR-15, AR-10, and LR-308 rifles. The main exception is Colt AR-15s made between 1991 and late 2009, which use a larger .172 inch pin and need the large pin version instead. If you're not sure, push a pin part way out of your lower and measure its diameter.
Is the CMC 92702 hard to install?
Not at all. Because the entire fire control group is self-contained in one housing, you just knock out your old trigger pins, drop the unit in, reinstall the pins, and tighten the pinset screws. Most people have it done in a few minutes with basic tools and no gunsmithing required.
What kind of shooting is the 2lb/2lb pull best for?
The light 2-pound set and 2-pound release give you a crisp, predictable break with a short reset, which makes it a strong pick for precision work, target shooting, and hunting. The consistent pull helps shrink group sizes on a rifle that came with a gritty factory trigger. It's a light pull, so it rewards good trigger discipline.
Can I adjust the pull weight on the CMC 92702?
No, the pull weight is set at the factory and is not user adjustable. That's actually part of the appeal, since it keeps the feel repeatable and takes the trial-and-error out of the equation. If the trigger ever needs attention down the road, CMC backs it with a lifetime warranty.




Reviews
There are no reviews yet.