Description
Running a red dot on a classic 1911 used to mean sending your slide off for milling. This EGW mount skips all that. It replaces the factory rear sight in a G.I. style dovetail cut and gives you a solid platform for a Vortex Razor red dot, no permanent modifications to the slide. If you ever want your original sight back, the mount comes right off and the gun goes back to stock.
How the G.I. Cut Sight Mount Installs
Installation is straightforward for anyone comfortable with a sight pusher. You press the old rear sight out of the dovetail, slide this mount in from left to right with the muzzle pointed forward, and the progressive taper on the dovetail helps it seat tight and secure. The red dot bolts onto the mount with the included hardware, and EGW recommends a dab of blue Loctite on the screws torqued to 15 in/lbs. The screws take a 5/64 inch allen wrench. Because dovetail dimensions vary slightly from gun to gun, a little hand fitting may be needed, and a lot of folks have a gunsmith handle the fit to make sure it holds zero properly.
What the Vortex Razor Mount Is Built From
This is machined from 7075 aluminum and finished in a matte black hardcoat anodize, so it is tough without adding much weight. The direct dovetail design sits the optic lower than a lot of rail adapter setups, which means a cleaner profile and quicker sight pickup. It fits Springfield 1911A1 models and a long list of Iver Johnson 1911A1 variants, along with any 1911 using a true G.I. style rear sight cut.
Optics the G.I. Cut Mount Accepts
Beyond the Vortex Razor, this same footprint accepts the C-More RTS and STS red dots, so you have some flexibility in which optic you run. Worth knowing up front: it does not fit the Vortex Venom or Viper, which use a different footprint and need a different EGW mount.
Key Specifications
- Manufacturer: EGW (Evolution Gun Works)
- Manufacturer Part Number: 49429
- UPC: 841370114399
- Material: 7075 Aluminum
- Finish: Matte Black Hardcoat Anodized Type III
- Color: Black
- Mount Type: Dovetail / Fixed, 1-Piece
- Fits Sight Cut: G.I. Style Rear Sight Cut
- Optic Compatibility: Vortex Razor, C-More RTS, STS, STS2
- Inclination: 0 MOA
- Dovetail Width: 0.347 in
- Overall Length: 1.831 in
- Overall Width: 1.062 in
- Hardware: Mounting screws (5/64 in allen), uses 15 in/lbs torque
- Made In: USA
What’s Included
- EGW G.I. cut Vortex Razor sight mount
- Mounting hardware
- Installation instructions
Frequently Asked Questions
Does the G.I. cut sight mount require milling my 1911 slide?
No milling needed. The mount installs directly into your existing G.I. style rear sight dovetail after you press out the factory rear sight. If you ever want to go back to irons, you can pull the mount off and reinstall your original sight.
Will this mount work with a Vortex Venom or Viper?
No, this one is cut for the Vortex Razor footprint and does not fit the Venom or Viper. Those optics use a different footprint, so you would need EGW's separate mount made for the Venom and Viper pattern.
What optics besides the Vortex Razor fit this mount?
The same footprint also accepts the C-More RTS, STS, and STS2 red dots. That gives you a little room to swap optics down the road without changing the mount.
Which 1911s does the G.I. cut sight mount fit?
It fits any 1911 with a true G.I. style rear sight cut, including Springfield 1911A1 and a wide range of Iver Johnson 1911A1 models. If you are not sure which dovetail your slide has, check against a 1911 dovetail reference before ordering, since GI, Novak, Bomar, and LPA cuts all use different mounts.




Reviews
There are no reviews yet.