0
0

Magne-Tech 3-Magnet Magnetic Locking Picatinny Receiver (Male)

UPC: 787790968269

$247.49

13 in stock

Online inventory may differ from in-store availability. 

Fast Shipping

Quick turnaround so you get your gear sooner.

Secure FFL-Friendly Checkout

Trusted checkout with industry-standard protection.

Family-Owned Business

Keeping Traditions Alive Since 1953

Secure Transactions provided with

Description

The Magne-Tech 3-Magnet Receiver is the base half of Magne-Tech's magnetic mounting system, the piece that clamps onto your rail and stays put. It's the male component that pairs with any of Magne-Tech's female ring mounts or accessory mounts, and it's what makes the whole snap-on, snap-off idea work. Three high-strength rare-earth magnets rated at over 15 pounds each hold your optic in place, backed up by a dual-redundant locking mechanism that guards against anything popping loose when you don't want it to.

What the 3-Magnet Receiver Actually Does

Think of this as the anchor point. You mount it to your Picatinny rail once, zero your setup, and from there you can pull your scope or accessory off, store it, and pop it right back on without chasing your zero all over again. Zero shift is repeatable to within 0.25 MOA for calibers up to about .308 Win recoil energy, roughly 18 in-lbs, as long as you reinstall in the same spot on the rail. Precisely machined angles and protrusions self-center the mating half every single time, which is the real trick behind the repeatability.

Build Quality on the Magnetic Locking Receiver

This one is cut from 7075-T6 aluminum alloy and finished with a MIL-A-8625 Type III hard-coat anodize, so it shrugs off wear while keeping weight reasonable. The base runs around 6.5 inches long and rides on standard MIL-STD-1913 rails, meaning it plays nice with AR platforms, bolt guns, and just about anything wearing a top rail. The locking side uses a spring-loaded lever that clips into the ring mount, plus a thumb screw you can cinch down to lock that lever out entirely for extra peace of mind.

Keep in mind this is the receiver only. You'll need a matching Magne-Tech female ring mount or accessory mount to complete the system, so grab the right tube size for your optic if you don't already have one. It's a smart pickup for anyone running both a day scope and a thermal or night optic on the same rifle and tired of re-zeroing every swap.

Key Specifications

  • Manufacturer: Magne-Tech
  • Manufacturer Part Number: 3-MAG-RECEIVER
  • UPC: 787790968269
  • Mount Type: Magnetic Locking Picatinny Rail Receiver (Male)
  • Rail Interface: MIL-STD-1913 Picatinny
  • Magnets: 3 rare-earth magnets, rated over 15 lbs each
  • Locking System: Dual-redundant (magnets plus spring-loaded side lock with thumb screw)
  • Material: 7075-T6 aluminum alloy
  • Finish: MIL-A-8625 Type III hard-coat anodize
  • Base Length: Approximately 6.5 inches
  • Zero Repeatability: Within 0.25 MOA (calibers up to ~.308 Win recoil, ~18 in-lbs)
  • Receiver Screw Torque: 30 in-lb

What’s Included

  • 3-Magnet Magnetic Locking Picatinny Rail Mount Receiver (Male)
  • Mounting hardware

Frequently Asked Questions

Does the Magne-Tech 3-Magnet Receiver come with a ring mount?

No, this listing is for the male receiver base only, which is the half that clamps to your rail. To complete the quick-detach system you'll need a matching Magne-Tech female ring mount or accessory mount, sold separately. Ring mounts come in 30mm, 34mm, and 1 inch, so pick the size that matches your scope tube.

Will this receiver hold zero when I swap optics?

Yes, that's the whole point of the system. Zero shift is repeatable to within 0.25 MOA for calibers up to roughly .308 Win recoil energy, thanks to self-centering machined surfaces that seat the mating half in the same place every time. Just make sure you reinstall the receiver in the same location along the rail and use it on rifles with the same bore-to-rail height.

What rifles does the Magne-Tech receiver fit?

It clamps to any standard MIL-STD-1913 Picatinny rail, so it works with a wide range of platforms including AR-style rifles and precision bolt guns. Just double-check that your rail has enough continuous length to fit the roughly 6.5-inch base. Rifles with short or segmented rail sections may only engage the outermost clamps.

How strong is the magnetic hold on this mount?

The receiver uses three high-strength rare-earth magnets, each rated at over 15 pounds of hold. On top of the magnetic grip, a spring-loaded side lock clips into the ring mount, and a thumb screw lets you lock that lever out entirely. Between the magnets and the mechanical lock, it stays put through recoil and rough handling.

Additional information

UPC

787790968269

Manufacturer

Manufacturer Part Number

3-MAG-RECEIVER

Reviews

There are no reviews yet.

Be the first to review “Magne-Tech 3-Magnet Magnetic Locking Picatinny Receiver (Male)”