Description
Anyone who runs more than one optic on a rifle knows the pain of re-zeroing every time you switch setups. Magne-Tech built this 3 inch Magnetic Picatinny Accessory Mount to get rid of that headache. It's the female half of their two-piece magnetic mounting system, meant to be bolted onto a red dot, magnifier, light, or any other gear with a standard picatinny footprint so that piece can travel between rifles without dragging a screwdriver and a bag of shims along with it.
How the 3 Inch Accessory Mount Locks In
Once this mount is attached to your accessory, it mates up with one of Magne-Tech's magnetic rail mounts using rare earth magnets built into the mating base, each rated at over 15 pounds of pull. That magnetic connection is backed up by a spring loaded side lever, and there's a thumb screw on the side that locks the lever out from accidental bumps when you want extra insurance. Magne-Tech has tested the system to hold zero within 0.25 MOA after repeated removal and reattachment, which is what makes running a day optic and a thermal or night vision unit on the same gun genuinely workable.
Machined From the Same Stock as the Rest of the Lineup
This accessory mount is machined from 7075-T6 aluminum alloy and finished with a Type III hard coat anodized coating, the same combination Magne-Tech uses across its rail mounts and receivers. It meets MIL-STD-1913 rail specs, so it lines up correctly with standard picatinny accessories and doesn't add any guesswork to the fit.
Pairing This Mount With a Rail Base
One thing worth knowing before it shows up at your door: this is the accessory side only. You'll need one of Magne-Tech's compatible male rail mounts installed on your rifle's picatinny rail to complete the connection. Once both halves are in place, pulling an optic off or snapping a new one on takes about as long as flipping the lever, and you can go straight back to shooting instead of walking back to the bench to check zero.
Key Specifications
- Manufacturer: Magne-Tech
- Manufacturer Part Number: MGN-PIC-ACC-MNT
- UPC: 787790968467
- Mount Length: 3 inches
- Mount Type: Female accessory mount (pairs with male rail mount)
- Material: 7075-T6 aluminum alloy
- Finish: MIL-A-8625 Type III hard coat anodized
- Rail Compatibility: MIL-STD-1913 Picatinny rail
- Zero Retention: Repeatable within 0.25 MOA after removal and reattachment
- Locking System: Magnetic connection with spring loaded side lever and thumb screw backup
- Compatible Accessories: Red dots, magnifiers, lights, and other standard picatinny footprint gear
What’s Included
- 3" Magnetic Picatinny Accessory Mount (Female)
- Mounting hardware
Frequently Asked Questions
Do I need anything else to use this 3 inch accessory mount?
Yes, this listing is for the female accessory mount only. You'll need one of Magne-Tech's male rail mounts installed on your rifle's picatinny rail before the magnetic connection will work.
What kind of accessories can I attach to this mount?
Anything with a standard picatinny footprint works, including red dots, magnifiers, weapon lights, and night vision or thermal units. Once it's bolted to your accessory, it snaps onto the mating rail mount just like any other Magne-Tech piece.
Will my optic hold zero if I keep taking it off and putting it back on?
Magne-Tech has tested this mounting system and found zero shift stays repeatable within 0.25 MOA on calibers up to roughly .308 recoil energy. That kind of consistency is what lets people move a single optic between multiple rifles without a trip back to the range to confirm point of impact.
How secure is the connection once it's snapped together?
The magnets in the mating rail base pull the two halves together with over 15 pounds of force each, and there's a spring loaded side lever plus a thumb screw for a second layer of security. Tighten the thumb screw down and the lever can't be bumped loose by accident.




Reviews
There are no reviews yet.