Description
This is Redding's .282 diameter heat-treated steel neck sizing bushing, part number 73282. It drops into any Redding bushing-style sizing die, including the popular Type S neck and full-length dies, and it's fully interchangeable with Wilson-style bushings too. The sizing diameters are hand polished to a surface hardness of Rc 60-62, which keeps sizing effort down and helps the brass glide through clean. The standard external dimensions run 1/2 inch O.D. by 3/8 inch long, so it fits right in alongside the rest of the Redding lineup.
The whole point of a bushing system is control. Instead of being locked into one fixed sizing dimension, you pick the exact inside neck diameter you want and swap bushings as your brass and loads change. The .282 size works for 6mm, 25 caliber, and 6.5mm cartridges depending on your neck wall thickness, and because Redding offers these in .001 inch increments, you can fine-tune tension without overworking the brass.
Picking the Right .282 Redding Bushing
The tried-and-true method is to measure the outside neck diameter of a loaded round with a good micrometer, then subtract your desired neck tension. Redding generally recommends subtracting .002 inch to allow for brass springback, though plenty of reloaders run anywhere from .001 to .004 depending on the rifle, the brass, and whether they're feeding a bolt gun or a gas gun. Buying a bushing one size up or down from your main choice is a cheap way to test what your barrel actually likes.
Getting the Most From This Steel Bushing
A couple of small habits make a real difference. Lube the case necks before sizing, and install the bushing with the numbers facing down for the best results. That orientation lets the bushing float slightly and self-center on the neck, which is a big part of why bushing dies produce such concentric, low-runout brass. If you're turning necks or chasing tighter groups, having a few bushings on hand around your target size gives you room to experiment.
Key Specifications
- Manufacturer: Redding
- Manufacturer Part Number: 73282
- UPC: 611760732829
- Bushing Diameter: .282 in
- Style: 73 Style Heat-Treated Steel
- Surface Hardness: Rc 60-62
- Outside Diameter: 1/2 in
- Length: 3/8 in
- Sizing Diameters: Hand polished
- Compatibility: All Redding bushing-style dies, interchangeable with Wilson-style bushings
- Typical Calibers: 6mm, 25 Cal, 6.5mm (depending on neck wall thickness)
What’s Included
- One Redding .282 heat-treated steel neck sizing bushing (73282)
Frequently Asked Questions
How do I know if the .282 bushing is right for my cartridge?
Measure the outside neck diameter of a loaded round with a micrometer, then subtract your desired neck tension. Redding recommends subtracting .002 inch to allow for brass springback, which lands you at your bushing size. Many reloaders run between .001 and .004 inch of tension depending on their brass and rifle.
Will this bushing fit my Redding Type S die?
Yes. This 73 style bushing drops into all Redding bushing-style sizing dies, including the Type S neck and full-length dies. It's also interchangeable with Wilson-style bushings, so it fits a wide range of setups.
What's the difference between the steel bushing and the Titanium Nitride version?
This .282 is the heat-treated steel version with hand-polished sizing diameters at a hardness of Rc 60-62. The Titanium Nitride bushings add a TiN surface treatment to further reduce sizing friction and ease stress on the brass. Both size the same, so the choice comes down to how slick you want the sizing to feel.
Which way does the bushing go into the die?
Install the bushing with the numbers facing down for the best results, and lube your case necks before sizing. Loading it this way lets the bushing float and self-center on the neck, which helps produce concentric brass with low runout.



Reviews
There are no reviews yet.