Description
If you're running a bolt-action 7mm Remington Magnum and chasing better accuracy out of your handloads, the Lee Precision Collet Neck Sizing Die is one of the smartest tools you can put on your bench. Instead of extruding the neck through a ring and dragging an expander ball back through it, this die uses a set of steel collet fingers to squeeze the case neck against a central mandrel. The result is a very straight, concentric neck sized evenly from top to bottom, which translates directly into lower runout and more consistent bullet tension.
How the 7mm Rem Mag Collet Die Keeps Brass Alive
Because this die only works the neck and leaves the fire-formed body and shoulder untouched, your cases stay matched to your chamber. That fire-formed fit is a big part of why neck-sized brass shoots so well, and it also means your cases last dramatically longer before they need full-length sizing. Neck-sized brass can last several times longer than brass that gets squeezed down full-length every cycle, and it generally needs less trimming too.
No Lube, No Mess with This Collet Neck Sizer
One of the nicest parts of the collet design is that it requires no case lubrication. There's no sliding of the case against a sizing ring, so there's nothing to wipe off afterward. A smear of grease on the collet cone inside the die is all the maintenance it really asks for. Setup is straightforward: run the die down so you feel firm resistance at the top of the stroke, and a common trick is to size, back off, rotate the case about an eighth of a turn, and size again for an even rounder neck.
A couple of things worth knowing up front. This die is built for cases fired in your own rifle and is intended for bolt guns, not autoloaders, slide actions, or lever guns. The decap mandrel and the .002-inch undersize mandrel for the undersized flash hole are sold separately if you want to go that route. For a precision-minded 7mm Rem Mag reloader who wants tight groups and long case life without fussing with lube, this is a hard die to beat for the money.
Key Specifications
- Manufacturer: Lee Precision
- Manufacturer Part Number: 91014
- UPC: 734307910143
- Cartridge: 7mm Remington Magnum
- Die Style: Collet Neck Sizing Die
- Die Material: Steel Collet
- Thread Size: 7/8"-14
- Lubrication Required: None
- Intended Use: Bolt-action rifles, cases fired in your own firearm
- Country of Manufacture: United States
What’s Included
- Lee Precision 7mm Remington Magnum collet neck sizing die
- Custom-fit plastic storage container
- Instructions
Frequently Asked Questions
Does the 7mm Rem Mag collet die need case lube?
No, this collet die requires no case lubrication. Because the collet simply squeezes the neck against a center mandrel, there's no sliding action to require lube and nothing to clean off your brass afterward. The only lube involved is a light smear of grease on the collet cone inside the die itself for smooth operation.
Can I use this die for brass fired in a different rifle?
Neck sizing is meant for cases that have been fired in the same rifle you'll reload them for. The die leaves the case body and shoulder fire-formed to your chamber, so cases from another gun may not chamber reliably. If you need to load for multiple rifles, a full-length sizing die is the better choice.
Is the collet neck sizing die good for semi-autos or lever guns?
No, this die is designed for bolt-action rifles and is not recommended for autoloaders, slide actions, or lever guns. Those actions benefit from full-length sizing to ensure reliable feeding and chambering. Neck sizing shines in a bolt gun where the fire-formed fit boosts accuracy and extends case life.
Does this die deprime the case, and does it come with a mandrel for that?
The collet die sizes the neck using the mandrel inside. The undersized flash hole decap mandrel and the .002-inch undersize decap mandrel are sold separately if you want those specific options. Check the mandrel setup that fits your reloading goals before ordering.




Reviews
There are no reviews yet.